Hydraulics & Fluid Machineries 1000+ MCQ with answer for SSC CPO

1. A Pelton wheel develops 1750 kW under a head of 100 metres while running at 200 r.p.m. and discharging 2500 litres of water per second. The unit speed of the wheel is
A. 10 r.p.m.
B. 20 r.p.m.
C. 40 r.p.m.
D. 80 r.p.m.
Answer : B

2. The hydraulic efficiency of an impulse turbine is the
A. Ratio of the actual power produced by the turbine to the energy actually supplied by the turbine
B. Ratio of the actual work available at the turbine to the energy imparted to the wheel
C. Ratio of the work done on the wheel to the energy of the jet
D. None of the above
Answer : C

3. Discharge of a centrifugal pump is (where N = Speed of the pump impeller)
A. Directly proportional to N
B. Inversely proportional to N
C. Directly proportional to N²
D. Inversely proportional to N²
Answer : A

4. Which of the following pump is successfully used for lifting water to the boilers?
A. Centrifugal pump
B. Reciprocating pump
C. Jet pump
D. Airlift pump
Answer : C

5. For starting an axial flow pump, its delivery valve should be
A. Closed
B. Open
C. Depends on starting condition and flow desired
D. Could be either open or closed
Answer : B

6. An impulse turbine is used for
A. Low head of water
B. High head of water
C. Medium head of water
D. High discharge
Answer : B

7. The centrifugal pump preferred for a specific speed between 80 to 160 r.p.m. is
A. Slow speed with radial flow at outlet
B. Medium speed with radial flow at outlet
C. High speed with radial flow at outlet
D. High speed with mixed flow at outlet
Answer : D

8. Delivery head of a centrifugal pump is
A. Directly proportional to N
B. Inversely proportional to N
C. Directly proportional to N²
D. Inversely proportional to N²
Answer : C

9. The cavitation in a hydraulic machine is mainly due to
A. Low velocity
B. High velocity
C. Low pressure
D. High pressure
Answer : C

10. The gross or total head of the turbine is the ________ of the water levels at the head race and tail race.
A. Sum
B. Difference
C. Product
D. None of these
Answer : B

11. The Thomson's turbine is __________ reaction turbine.
A. An axial flow
B. An inward flow
C. An outward flow
D. A mixed flow
Answer : B

12. By fitting an air vessel to the reciprocating pump, there is always a saving of work done and subsequently saving of power. This saving in case of a single acting reciprocating pump is
A. 39.2 %
B. 48.8 %
C. 84.8 %
D. 88.4 %
Answer : C

13. A Pelton wheel is
A. Tangential flow impulse turbine
B. Inward flow impulse turbine
C. Outward flow impulse turbine
D. Inward flow reaction turbine
Answer : A

14. A double overhung Pelton wheel has
A. Two jets
B. Two runners
C. Four jets
D. Four runners
Answer : B

15. Power required (in watts) to drive a centrifugal pump is (where H_m = Manometric head in metres, w = Specific weight in N/m³, Q = Discharge of the pump in m³/s, and ?_o = Overall efficiency of the pump)
A. (w H_m) / (Q × ?_o)
B. (w H_m Q) / ?_o
C. (w Q) / (H_m × ?_o)
D. (w Q ?_o) / H_m
Answer : B

16. Motion of a liquid in a volute casing of a centrifugal pump is an example of
A. Rotational flow
B. Radial
C. Forced spiral vortex flow
D. Spiral vortex flow
Answer : D

17. The maximum number of jets, generally, employed in an impulse turbine without jet interference are
A. Two
B. Four
C. Six
D. Eight
Answer : C

18. Which of the following pump is suitable for small discharge and high heads?
A. Centrifugal pump
B. Axial flow pump
C. Mixed flow pump
D. Reciprocating pump
Answer : D

19. In a reciprocating pump, air vessels are used to
A. Smoothen the flow
B. Reduce suction head
C. Increase delivery head
D. Reduce acceleration head
Answer : D

20. Manometric head, in case of a centrifugal pump, is equal to
A. Suction lift + Loss of head in suction pipe due to friction + Delivery lift + Loss of head in delivery pipe due to friction + Velocity head in the delivery pipe
B. Workdone per kN of water Losses within the impeller
C. Energy per kN at outlet of impeller Energy per kN at inlet of impeller
D. All of the above
Answer : D

21. Power required to drive a centrifugal pump is directly proportional to ________ of its impeller.
A. Diameter
B. Square of diameter
C. Cube of diameter
D. Fourth power of diameter
Answer : D

22. Low specific speed of turbine implies it is
A. Propeller turbine
B. Francis turbine
C. Impulse turbine
D. Any one of the above
Answer : C

23. A Francis turbine is used when the available head of water is
A. 0 to 25 m
B. 25 m to 250 m
C. Above 250 m
D. None of these
Answer : B

24. A hydraulic press is a device used
A. To store pressure energy which may be supplied to a machine later on
B. To increase the intensity of pressure of water by means of energy available from a large quantity of water at a low pressure
C. To lift larger load by the application of a comparatively much smaller force
D. All of the above
Answer : C

25. The power developed by a turbine is (where H = Head of water under which the turbine is working)
A. Directly proportional to H^1/2
B. Inversely proportional to H^1/2
C. Directly proportional to H^3/2
D. Inversely proportional to H^3/2
Answer : C

26. Reciprocating pumps are no more to be seen in industrial applications (in comparison to centrifugal pumps) because of
A. High initial and maintenance cost
B. Lower discharge
C. Lower speed of operation
D. Necessity of air vessel
Answer : A

27. The overall efficiency of a reaction turbine is the ratio of
A. Power produced by the turbine to the energy actually supplied by the turbine
B. Actual work available at the turbine to the energy imparted to the wheel
C. Workdone on the wheel to the energy (or head of water) actually supplied to the turbine
D. None of the above
Answer : A

28. Which of the following statement is correct?
A. The centrifugal pump is suitable for large discharge and smaller heads.
B. The centrifugal pump requires less floor area and simple foundation as compared to reciprocating pump.
C. The efficiency of centrifugal pump is less as compared to reciprocating pump.
D. All of the above
Answer : D

29. A hydraulic ram is a device used to
A. Store the energy of water
B. Increase the pressure of water
C. To lift water from deep wells
D. To lift small quantity of water to a greater height when a large quantity of water is available at a smaller height
Answer : D

30. The maximum hydraulic efficiency of an impulse turbine is (where ? = Angle of blade tip at outlet)
A. (1 + cos ?)/2
B. (1 - cos ?)/2
C. (1 + sin ?)/2
D. (1 - sin ?)/2
Answer : A

31. The specific speed from 160 to 500 r.p.m. of a centrifugal pump indicates that the pump is
A. Slow speed with radial flow at outlet
B. Medium speed with radial flow at outlet
C. High speed with radial flow at outlet
D. High speed with axial flow at outlet
Answer : D

32. In an outward flow reaction turbine
A. The water flows parallel to the axis of the wheel
B. The water enters at the centre of the wheel and then flows towards the outer periphery of the wheel
C. The water enters the wheel at the outer periphery and then flows towards the centre of the wheel
D. The flow of water is partly radial and partly axial
Answer : B

33. When a piping system is made up primarily of friction head and very little of vertical lift, then pump characteristics should be
A. Horizontal
B. Nearly horizontal
C. Steep
D. First rise and then fall
Answer : B

34. A hydraulic coupling belongs to the category of
A. Power absorbing machines
B. Power developing machines
C. Energy transfer machines
D. Energy generating machines
Answer : C

35. Geometric similarity is said to exist between the model and the prototype, if both of them
A. Have identical velocities
B. Are equal in size and shape
C. Are identical in shape, but differ only in size
D. Have identical forces
Answer : C

36. A turbine develops 10000 kW under a head of 25 metres at 135 r.p.m. Its specific speed is
A. 175.4 r.p.m.
B. 215.5 r.p.m.
C. 241.5 r.p.m.
D. 275.4 r.p.m
Answer : C

37. The water in a jet propelled boat is drawn through the openings facing the direction of motion of the boat. The efficiency of propulsion is given by
A. 2V/(v_r - v)
B. 2V/(v_r + v)
C. V/(v_r - v)
D. V/(v_r + v)
Answer : B

38. Which type of the pump is different from others in the same group?
A. Screw pump
B. Gear pump
C. Cam and piston pump
D. Plunger pump
Answer : D

39. Axial flow pump is started with its delivery valve
A. Kept fully closed
B. Kept fully open
C. Irrespective of any position
D. Kept 50% open
Answer : B

40. According to fan laws, for fans having constant wheel diameter, the air or gas capacity varies
A. Directly as fan speed
B. Square of fan speed
C. Cube of fan speed
D. Square root of fan speed
Answer : A

41. The power produced by the reaction turbine is ________ to the head of water.
A. Directly proportional
B. Inversely proportional
C. 4th power
D. None of these
Answer : A

42. According to fan laws, at constant speed and capacity, the pressure and power vary
A. Directly as the air or gas density
B. Inversely as square root of density
C. Inversely as density
D. As square of density
Answer : A

43. The flow rate in gear pump
A. Increases with increase in pressure
B. Decreases with increase in pressure
C. More or less remains constant with increase in pressure
D. Unpredictable
Answer : C

44. The maximum number of jets generally employed in impulse turbine without jet interference is
A. 4
B. 6
C. 8
D. 12
Answer : B

45. Hydraulic accumulator is used for
A. Accumulating oil
B. Supplying large quantities of oil for very short duration
C. Generally high pressures to operate hydraulic machines
D. Supplying energy when main supply fails
Answer : D

46. The unit discharge through the turbine is
A. Q/?H
B. Q/H
C. Q/H^3/2
D. Q/H²
Answer : A

47. Which of the following pump is successfully used for lifting water from deep wells?
A. Centrifugal pump
B. Reciprocating pump
C. Jet pump
D. Air lift pump
Answer : D

48. If the net positive suction head (NPSH) requirement for the pump is not satisfied, then
A. No flow will take place
B. Cavitation will be formed
C. Efficiency will be low
D. Excessive power will be consumed
Answer : B

49. Braking jet in an impulse turbine is used
A. To break the jet of water
B. To bring the runner to rest in a short time
C. To change the direction of runner
D. None of these
Answer : B

50. Which of the following statement is correct?
A. In an impulse turbine, the water impinges on the buckets with pressure energy.
B. In a reaction turbine, the water glides over the moving vanes with kinetic energy.
C. In an impulse turbine, the pressure of the flowing water remains unchanged and is equal to atmospheric pressure.
D. In a reaction turbine, the pressure of the flowing water increases after gliding over the vanes.
Answer : C