Hydraulics & Fluid Machineries MCQ Solved Paper for LIC ADO

1. Impulse turbine is generally fitted
A. At the level of tail race
B. Little above the tail race
C. Slightly below the tail race
D. About 2.5 m above the tail race to avoid cavitations.
Answer : B

2. The force exerted by a jet of water impinging normally on a plate which due to the impact of jet, moves in the direction of jet with a velocity v is
A. [wa (V - v)]/2g
B. [wa (V - v)]/g
C. [wa (V - v)²]/2g
D. [wa (V - v²)]/g
Answer : D

3. Power required (in watts) to drive a centrifugal pump is (where H_m = Manometric head in metres, w = Specific weight in N/m³, Q = Discharge of the pump in m³/s, and ?_o = Overall efficiency of the pump)
A. (w H_m) / (Q × ?_o)
B. (w H_m Q) / ?_o
C. (w Q) / (H_m × ?_o)
D. (w Q ?_o) / H_m
Answer : B

4. The specific speed of a turbine is the speed of an imaginary turbine, identical with the given turbine, which
A. Delivers unit discharge under unit head
B. Delivers unit discharge under unit speed
C. Develops unit power under unit head
D. Develops unit power under unit speed
Answer : C

5. In order to avoid cavitation in centrifugal pumps
A. The suction pressure should be high
B. The delivery pressure should be high
C. The suction pressure should be low
D. The delivery pressure should be low
Answer : A

6. A hydraulic intensifier normally consists of
A. Two cylinders, two rams and a storage device
B. A cylinder and a ram
C. Two coaxial rams and two cylinders
D. A cylinder, a piston, storage tank and control valve
Answer : C

7. The depth of the bucket for a Pelton wheel is generally ________ the diameter of jet.
A. Equal to
B. 1.2 times
C. 1.8 times
D. Double
Answer : B

8. Manometric head, in case of a centrifugal pump, is equal to
A. Suction lift + Loss of head in suction pipe due to friction + Delivery lift + Loss of head in delivery pipe due to friction + Velocity head in the delivery pipe
B. Workdone per kN of water Losses within the impeller
C. Energy per kN at outlet of impeller Energy per kN at inlet of impeller
D. All of the above
Answer : D

9. Which of the following statement is wrong?
A. The reaction turbines are used for low head and high discharge.
B. The angle of taper on draft tube is less than 8°.
C. An impulse turbine is generally fitted slightly above the tail race.
D. A Francis turbine is an impulse turbine.
Answer : D

10. The angle of taper on draft tube is
A. Greater than 15°
B. Greater than 8°
C. Greater than 5°
D. Less than 8°
Answer : D

11. Any change in load is adjusted by adjusting following parameter on turbine
A. Net head
B. Absolute velocity
C. Blade velocity
D. Flow
Answer : D

12. The power developed by a turbine is (where H = Head of water under which the turbine is working)
A. Directly proportional to H^1/2
B. Inversely proportional to H^1/2
C. Directly proportional to H^3/2
D. Inversely proportional to H^3/2
Answer : C

13. The discharge through a reaction turbine with increase in unit speed
A. Increases
B. Decreases
C. Remain unaffected
D. First increases and then decreases
Answer : B

14. Which of the following turbine is preferred for a specific speed of 60 to 300 r.p.m.?
A. Pelton wheel
B. Francis turbine
C. Kaplan turbine
D. None of these
Answer : B

15. When a piping system is made up primarily of vertical lift and very little pipe friction, the pump characteristics should be
A. Horizontal
B. Nearly horizontal
C. Steep
D. First rise and then fall
Answer : C

16. Power required to drive a centrifugal pump is directly proportional to ________ of its impeller.
A. Diameter
B. Square of diameter
C. Cube of diameter
D. Fourth power of diameter
Answer : D

17. Braking jet in an impulse turbine is used
A. To break the jet of water
B. To bring the runner to rest in a short time
C. To change the direction of runner
D. None of these
Answer : B

18. The maximum number of jets generally employed in impulse turbine without jet interference is
A. 4
B. 6
C. 8
D. 12
Answer : B

19. In a centrifugal pump, the liquid enters the pump
A. At the top
B. At the bottom
C. At the canter
D. From sides
Answer : C

20. The specific speed from 160 to 500 r.p.m. of a centrifugal pump indicates that the pump is
A. Slow speed with radial flow at outlet
B. Medium speed with radial flow at outlet
C. High speed with radial flow at outlet
D. High speed with axial flow at outlet
Answer : D

21. By fitting an air vessel to the reciprocating pump, there is always a saving of work done and subsequently saving of power. The saving in case of a double acting reciprocating pump is
A. 39.2 %
B. 48.8 %
C. 84.8 %
D. 88.4 %
Answer : A

22. Slip of a reciprocating pump is defined as the
A. Ratio of actual discharge to the theoretical discharge
B. Sum of actual discharge and the theoretical discharge
C. Difference of theoretical discharge and the actual discharge
D. Product of theoretical discharge and the actual discharge
Answer : C

23. The specific speed (Ns) of a centrifugal pump is given by
A. (N?Q)/H^2/3
B. (N?Q)/H^3/4
C. (N?Q)/H
D. (N?Q)/H^5/4
Answer : B

24. If the net positive suction head (NPSH) requirement for the pump is not satisfied, then
A. No flow will take place
B. Cavitation will be formed
C. Efficiency will be low
D. Excessive power will be consumed
Answer : B

25. Guide angle as per the aerofoil theory of Kaplan turbine blade design is defined as the angle between
A. Lift and resultant force
B. Drag and resultant force
C. Lift and tangential force
D. Lift and drag
Answer : A

26. Reaction turbines are used for
A. Low head
B. High head
C. High head and low discharge
D. Low head and high discharge
Answer : D

27. Which of the following pump is suitable for small discharge and high heads?
A. Centrifugal pump
B. Axial flow pump
C. Mixed flow pump
D. Reciprocating pump
Answer : D

28. A turbine develops 10000 kW under a head of 25 metres at 135 r.p.m. Its specific speed is
A. 175.4 r.p.m.
B. 215.5 r.p.m.
C. 241.5 r.p.m.
D. 275.4 r.p.m
Answer : C

29. The runaway speed of a hydraulic turbine is the speed
A. At full load
B. At which there will be no damage to the runner
C. Corresponding to maximum overload permissible
D. At which the turbine will run freely without load
Answer : D

30. Discharge of a centrifugal pump is
A. Directly proportional to diameter of its impeller
B. Inversely proportional to diameter of its impeller
C. Directly proportional to (diameter)² of its impeller
D. Inversely proportional to (diameter)² of its impeller
Answer : D

31. A centrifugal pump will start delivering liquid only when the pressure rise in the impeller is equal to the
A. Kinetic head
B. Velocity head
C. Manometric head
D. Static head
Answer : C

32. The unit discharge through the turbine is
A. Q/?H
B. Q/H
C. Q/H^3/2
D. Q/H²
Answer : A

33. In a centrifugal pump, the regulating valve is provided on the
A. Casing
B. Delivery pipe
C. Suction pipe
D. Impeller
Answer : B

34. Runaway speed of a hydraulic turbine is
A. Full load speed
B. The speed at which turbine runner will be damaged
C. The speed if the turbine runner is allowed to revolve freely without load and with the wicket gates wide open
D. The speed corresponding to maximum overload permissible
Answer : C

35. If a pump is handling water and is discharging a certain flow Q at a constant total dynamic head requiring a definite B.H.P., the same pump when handling a liquid of specific gravity 0.75 and viscosity nearly same as of water, the horse power required will be
A. Same
B. 0.75 B.H.P.
C. B.H.P./0.75
D. 1.5 B.H.P.
Answer : B

36. The hydraulic efficiency of an impulse turbine is maximum when velocity of wheel is _______ of the jet velocity,
A. One-fourth
B. One-half
C. Three-fourth
D. Double
Answer : B

37. The discharge through a reaction turbine ________ with the increase in unit speed.
A. Decreases
B. Increases
C. Remain same
D. None of these
Answer : A

38. The unit speed of the turbine runner is
A. N/?H
B. N/H
C. N/H^3/2
D. N/H²
Answer : A

39. A hydraulic coupling belongs to the category of
A. Power absorbing machines
B. Power developing machines
C. Energy transfer machines
D. Energy generating machines
Answer : C

40. Low specific speed of turbine implies it is
A. Propeller turbine
B. Francis turbine
C. Impulse turbine
D. Any one of the above
Answer : C

41. Which type of the pump is different from others in the same group?
A. Screw pump
B. Gear pump
C. Cam and piston pump
D. Plunger pump
Answer : D

42. The mechanical efficiency of an impulse turbine is
A. Ratio of the actual power produced by the turbine to the energy actually supplied by the turbine
B. Ratio of the actual work available at the turbine to the energy imparted to the wheel
C. Ratio of the Work done on the wheel to the energy of the jet
D. None of the above
Answer : B

43. The efficiency of a hydraulic press is given by (where W = Weight lifted by ram, P = Force applied on plunger, A = Area of ram, and a = Area of plunger)
A. (W/p) × (A/a)
B. (p/W) × (a/A)
C. (W/p) × (a/A)
D. (p/W) × (A/a)
Answer : C

44. Kinematic similarity is said to exist between the model and the prototype, if both of them
A. Have identical velocities
B. Are equal in size and shape
C. Are identical in shape, but differ only in size
D. Have identical forces
Answer : A

45. Which of the following statement is correct?
A. In an impulse turbine, the water impinges on the buckets with pressure energy.
B. In a reaction turbine, the water glides over the moving vanes with kinetic energy.
C. In an impulse turbine, the pressure of the flowing water remains unchanged and is equal to atmospheric pressure.
D. In a reaction turbine, the pressure of the flowing water increases after gliding over the vanes.
Answer : C

46. The overall efficiency of a reaction turbine is the ratio of
A. Power produced by the turbine to the energy actually supplied by the turbine
B. Actual work available at the turbine to the energy imparted to the wheel
C. Workdone on the wheel to the energy (or head of water) actually supplied to the turbine
D. None of the above
Answer : A

47. Discharge of a centrifugal pump is (where N = Speed of the pump impeller)
A. Directly proportional to N
B. Inversely proportional to N
C. Directly proportional to N²
D. Inversely proportional to N²
Answer : A

48. Low specific speed of a pump implies it is
A. Centrifugal pump
B. Mixed flow pump
C. Axial flow pump
D. None of the above
Answer : A

49. Specific speed for reaction turbines ranges from
A. 0 to 4.5
B. 10 to 100
C. 80 to 200
D. 250 to 300
Answer : B

50. The force exerted by a jet of water (in a direction normal to flow) impinging on a fixed plate inclined at an angle ? with the jet is
A. waV/2g × sin?
B. waV/g × sin?
C. waV²/2g × sin2?
D. waV²/g × sin?
Answer : C