Hydraulics & Fluid Machineries MCQ Solved Paper for RRB Group D

1. The water in a jet propelled boat is drawn through the openings facing the direction of motion of the boat. The efficiency of propulsion is given by
A. 2V/(v_r - v)
B. 2V/(v_r + v)
C. V/(v_r - v)
D. V/(v_r + v)
Answer : B

2. In a reaction turbine, the draft tube is used
A. To run the turbine full
B. To prevent air to enter the turbine
C. To increase the head of water by an amount equal to the height of the runner outlet above the tail race
D. To transport water to downstream
Answer : C

3. Multistage centrifugal pumps are used to
A. Give high discharge
B. Produce high heads
C. Pump viscous fluids
D. All of these
Answer : B

4. In a Francis turbine runner, the numbers of blades are generally between
A. 2 to 4
B. 4 to 8
C. 8 to 16
D. 16 to 24
Answer : D

5. When a piping system is made up primarily of vertical lift and very little pipe friction, the pump characteristics should be
A. Horizontal
B. Nearly horizontal
C. Steep
D. First rise and then fall
Answer : C

6. The function of guide vanes in a reaction turbine is to
A. Allow the water to enter the runner without shock
B. Allow the water to flow over them, without forming eddies
C. Allow the required quantity of water to enter the turbine
D. All of the above
Answer : D

7. The specific speed of a hydraulic turbine depends upon
A. Speed and power developed
B. Discharge and power developed
C. Speed and head of water
D. Speed, power developed and head of water
Answer : D

8. The runaway speed of a hydraulic turbine is the speed
A. At full load
B. At which there will be no damage to the runner
C. Corresponding to maximum overload permissible
D. At which the turbine will run freely without load
Answer : D

9. High specific speed of turbine implies it is
A. Propeller turbine
B. Francis turbine
C. Impulse turbine
D. None of the above
Answer : A

10. A hydraulic accumulator normally consists of
A. Two cylinders, two rams and a storage device
B. A cylinder and a ram
C. Two coaxial rams and two cylinders
D. A cylinder, a piston, storage tank and control valve
Answer : B

11. Head developed by a centrifugal pump is
A. Proportional to diameter of impeller
B. Proportional to speed of impeller
C. Proportional to diameter and speed of impeller
D. None of the above
Answer : C

12. Which of the following pump is successfully used for lifting water from deep wells?
A. Centrifugal pump
B. Reciprocating pump
C. Jet pump
D. Air lift pump
Answer : D

13. The speed of a turbine runner is
A. Directly proportional to H^1/2
B. Inversely proportional to H^1/2
C. Directly proportional to H^3/2
D. Inversely proportional to H^3/2
Answer : A

14. The hydraulic efficiency of a reaction turbine, is the ratio of
A. Power produced by the turbine to the energy actually supplied by the turbine
B. Actual work available at the turbine to energy imparted to the wheel
C. Workdone on the wheel to the energy (or head of water) actually supplied to the turbine
D. None of the above
Answer : C

15. For 450 m head of water, _________ shall be used.
A. Pelton wheel
B. Kaplan turbine
C. Francis turbine
D. None of these
Answer : A

16. The force exerted by a jet of water impinging normally on a plate which due to the impact of jet, moves in the direction of jet with a velocity v is
A. [wa (V - v)]/2g
B. [wa (V - v)]/g
C. [wa (V - v)²]/2g
D. [wa (V - v²)]/g
Answer : D

17. According to fan laws, at constant speed and capacity, the pressure and power vary
A. Directly as the air or gas density
B. Inversely as square root of density
C. Inversely as density
D. As square of density
Answer : A

18. The ratio of actual work available at the turbine to the energy imparted to the wheel is known as ________ efficiency.
A. Hydraulic
B. Mechanical
C. Overall
D. None of these
Answer : B

19. In reaction turbine, draft tube is used
A. To transport water downstream without eddies
B. To convert the kinetic energy to flow energy by a gradual expansion of the flow cross-section
C. For safety of turbine
D. To increase flow rate
Answer : B

20. If the ratios of all the corresponding linear dimensions are equal, then the model and the prototype are said to have
A. Geometric similarity
B. Kinematic similarity
C. Dynamic similarity
D. None of these
Answer : A

21. Discharge of a centrifugal pump is (where N = Speed of the pump impeller)
A. Directly proportional to N
B. Inversely proportional to N
C. Directly proportional to N²
D. Inversely proportional to N²
Answer : A

22. The overall efficiency of a reaction turbine is the ratio of
A. Power produced by the turbine to the energy actually supplied by the turbine
B. Actual work available at the turbine to the energy imparted to the wheel
C. Workdone on the wheel to the energy (or head of water) actually supplied to the turbine
D. None of the above
Answer : A

23. Overall efficiency of a centrifugal pump is the ratio of
A. Energy available at the impeller to the energy supplied to the pump by the prime mover
B. Actual workdone by the pump to the energy supplied to the pump by the prime mover
C. Energy supplied to the pump to the energy available at the impeller
D. Manometric head to the energy supplied by the impeller per kN of water
Answer : B

24. Geometric similarity is said to exist between the model and the prototype, if both of them
A. Have identical velocities
B. Are equal in size and shape
C. Are identical in shape, but differ only in size
D. Have identical forces
Answer : C

25. The Thomson's turbine is __________ reaction turbine.
A. An axial flow
B. An inward flow
C. An outward flow
D. A mixed flow
Answer : B

26. Which of the following turbine is preferred for a specific speed of 60 to 300 r.p.m.?
A. Pelton wheel
B. Francis turbine
C. Kaplan turbine
D. None of these
Answer : B

27. The hydraulic efficiency of an impulse turbine is maximum when velocity of wheel is _______ of the jet velocity,
A. One-fourth
B. One-half
C. Three-fourth
D. Double
Answer : B

28. The relation between hydraulic efficiency (?_h), mechanical efficiency (?_m) and overall efficiency (?_o) is
A. ?_h = ?_o × ?_m
B. ?_m = ?_m × ?_h
C. ?_o = ?_h × ?_m
D. None of these
Answer : C

29. Kinematic similarity is said to exist between the model and the prototype, if both of them
A. Have identical velocities
B. Are equal in size and shape
C. Are identical in shape, but differ only in size
D. Have identical forces
Answer : A

30. The static head of a centrifugal pump is equal to the ________ of suction head and delivery head.
A. Product
B. Difference
C. Sum
D. None of these
Answer : C

31. The hydraulic efficiency of an impulse turbine is the
A. Ratio of the actual power produced by the turbine to the energy actually supplied by the turbine
B. Ratio of the actual work available at the turbine to the energy imparted to the wheel
C. Ratio of the work done on the wheel to the energy of the jet
D. None of the above
Answer : C

32. The maximum efficiency of jet propulsion of a ship with inlet orifices at right angles to the direction of motion of ship, is
A. 40 %
B. 50 %
C. 60 %
D. 80 %
Answer : B

33. The power developed by a turbine is (where H = Head of water under which the turbine is working)
A. Directly proportional to H^1/2
B. Inversely proportional to H^1/2
C. Directly proportional to H^3/2
D. Inversely proportional to H^3/2
Answer : C

34. Francis, Kaplan and propeller turbines fall under the category of
A. Impulse turbines
B. Reaction turbines
C. Axial flow turbines
D. Mixed flow turbines
Answer : B

35. Low specific speed of turbine implies it is
A. Propeller turbine
B. Francis turbine
C. Impulse turbine
D. Any one of the above
Answer : C

36. The discharge through a reaction turbine with increase in unit speed
A. Increases
B. Decreases
C. Remain unaffected
D. First increases and then decreases
Answer : B

37. For small discharge at high pressure, following pump is preferred
A. Centrifugal
B. Axial flow
C. Mixed flow
D. Reciprocating
Answer : D

38. The unit speed of the turbine runner is
A. N/?H
B. N/H
C. N/H^3/2
D. N/H²
Answer : A

39. The angle of taper on draft tube is
A. Greater than 15°
B. Greater than 8°
C. Greater than 5°
D. Less than 8°
Answer : D

40. If a pump is handling water and is discharging a certain flow Q at a constant total dynamic head requiring a definite B.H.P., the same pump when handling a liquid of specific gravity 0.75 and viscosity nearly same as of water, the horse power required will be
A. Same
B. 0.75 B.H.P.
C. B.H.P./0.75
D. 1.5 B.H.P.
Answer : B

41. Centrifugal pump is started with its delivery valve
A. Kept fully closed
B. Kept fully open
C. Irrespective of any position
D. Kept 50% open
Answer : A

42. For very high discharge at low pressure such as for flood control and irrigation applications, following type of pump is preferred
A. Centrifugal
B. Axial flow
C. Reciprocating
D. Mixed flow
Answer : B

43. Dynamic similarity is said to exist between the model and the prototype, if both of them
A. Have identical velocities
B. Are equal in size and shape
C. Are identical in shape, but differ only in size
D. None of the above
Answer : D

44. Which of the following is not an impulse turbine?
A. Girad turbine
B. Turgo turbine
C. Pelton wheel
D. Kaplan turbine
Answer : D

45. If the net positive suction head (NPSH) requirement for the pump is not satisfied, then
A. No flow will take place
B. Cavitation will be formed
C. Efficiency will be low
D. Excessive power will be consumed
Answer : B

46. The specific speed from 160 to 500 r.p.m. of a centrifugal pump indicates that the pump is
A. Slow speed with radial flow at outlet
B. Medium speed with radial flow at outlet
C. High speed with radial flow at outlet
D. High speed with axial flow at outlet
Answer : D

47. Which of the following pump is successfully used for lifting water to the boilers?
A. Centrifugal pump
B. Reciprocating pump
C. Jet pump
D. Airlift pump
Answer : C

48. In impulse Turbine, energy available at the inlet is in the form of
A. Potential Energy
B. Strain Energy
C. Kinetic energy
D. None of these
Answer : C

49. Mechanical efficiency of a centrifugal pump is the ratio of
A. Energy available at the impeller to the energy supplied to the pump by the prime mover
B. Actual workdone by the pump to the energy supplied to the pump by the prime mover
C. Energy supplied to the pump to the energy available at the impeller
D. Manometric head to the energy supplied by the impeller per kN of water
Answer : A

50. A Pelton wheel develops 1750 kW under a head of 100 metres while running at 200 r.p.m. and discharging 2500 litres of water per second. The unit speed of the wheel is
A. 10 r.p.m.
B. 20 r.p.m.
C. 40 r.p.m.
D. 80 r.p.m.
Answer : B