RRB JE - Design of Steel Structures 1000+ MCQ [Solved] PDF Download

1. An axial loaded column is supported on a slab base whose projection is 8 cm. If the intensity of pressure from concrete is 40 kg/cm² and allowable bending stress in slab base is 1890 kg/cm², the thickness (t) of the slab base, is
A. t = ?(21/64)
B. t = ?(64/21)
C. t = 21/64
D. t = 64/21
Answer : B

2. Study the following statements. (i) Top lateral bracing prevents the sides-way buckling of the chord. (ii) Sway bracing keeps the rectangular shape of the bridge crosssection. (iii) Sway bracing transfers the load from top of end posts to bearings. The correct answer is
A. Only (i)
B. Both (i) and (ii)
C. Both (i) and (iii)
D. All (i), (ii) and (iii)
Answer : B

3. By providing sufficient edge distance, which of the following failures of riveted joint can be avoided?
A. Tension failure of the plate
B. Shear failure of the rivet
C. Shear failure of the plate
D. Crushing failure of the rivet
Answer : C

4. A single angle in tension is connected by one leg only. If the areas of connecting and outstanding legs are respectively a and b, net effective area of the angle, is
A. a - [b/{1 + 0.35 (b/a)}]
B. a + [b/{1 + 0.35 (b/a)}]
C. a - [b/{1 + 0.2 (b/a)}]
D. a + [b/{1 + 0.2 (b/a)}]
Answer : B

5. The area A_p of cover plates in one flange of a built up beam, is given by
A. A_p = Z_reqr + Z_beam/h
B. A_p = Z_reqr + Z_beam/A
C. A_p = Z_reqr × Z_beam/h
D. A_p = Z_reqr - Z_beam/h
Answer : D

6. For a steel grillage footing to support two unequal column loads
A. Line of action of the resultant of two column loads, is made to coincide with the centre of gravity of the base of the footing
B. Trapezoidal shape is used for the base footing
C. Projections of beams on either side in lower tier are such that bending moments under columns are equal
D. All the above
Answer : D

7. The maximum spacing of vertical stiffeners is
A. 1.33 d
B. 1.25 d
C. 1.5 d
D. 1.75 d Where d is the distance between flange angles
Answer : C

8. Diameter of a rivet hole is made larger than the diameter of the rivet by
A. 1.0 mm for rivet diameter upto 12 mm
B. 1.5 mm for rivet diameter exceeding 25 mm
C. 2.0 mm for rivet diameter over 25 mm
D. None of these
Answer : C

9. The connection of intermediate vertical stiffeners to the web, not subjected to external loads, shall be designed for a minimum shear force (kN/m) of
A. 75 t²/h
B. 125 t³/h²
C. 125 t²/h
D. 175 t²/h Where, t = the web thickness in mm and h = the outstand of stiffener in mm
Answer : C

10. Cold driven rivets range from
A. 6 to 10 mm in diameter
B. 10 to 16 mm in diameter
C. 12 to 22 mm in diameter
D. 22 to 32 mm in diameter
Answer : C

11. Pitch of tacking rivets, when double angles connected back to back and acting as tension members should not be more than
A. 500 mm
B. 600 mm
C. 1000 mm
D. 300 mm
Answer : C

12. In a tension member if one or more than one rivet holes are off the line, the failure of the member depends upon:
A. Pitch
B. Gauge
C. Diameter of the rivet holes
D. All the above
Answer : D

13. Pick up the correct statement from the following:
A. The minimum pitch should not be less than 2.5 times the gross diameter of the river
B. The minimum pitch should not be less than 12 times the gross diameter of the rivet
C. The maximum pitch should not exceed 10 times the thickness or 150 mm whichever is less in compression
D. All the above
Answer : A

14. If d is the distance between the flange angles of a plate girder, vertical stiffeners are provided at a distance not greater than
A. d but not less than 0.20 d
B. 1.25 d but not less than 0.33 d
C. 1.5 d but not less than 0.33 d
D. 2.0 d but not less than 0.50 d
Answer : B

15. In a grillage footing, the maximum shear force occurs at the
A. Edge of grillage beam
B. Centre of base plate
C. Centre of grillage beam
D. Centre of base plate
Answer : B

16. Rise of a Jack arch is kept about
A. 1/2 to 1/3 of the span
B. 1/3 to 1/4 of the span
C. 1/4 to 1/8 of the span
D. 1/8 to 1/12 of the span
Answer : D

17. In moment resistant connections, the moment resistance of riveted connection depends upon
A. Shear in rivets
B. Compression in rivets
C. Tension in rivets
D. Strength of rivets in bearing
Answer : C

18. Rolled steel angle sections are classified as
A. Equal angles
B. Unequal angles
C. Bulb angles
D. All the above
Answer : D

19. Pick up the incorrect statement from the following:
A. The nominal diameter of a rivet is its diameter before driving
B. The gross diameter of a rivet is the diameter of rivet hole
C. The gross area of a rivet is the cross-sectional area of the rivet hole
D. The diameter of a rivet hole is equal to the nominal diameter of the rivet plus 1.5 mm
Answer : D

20. For rivets in tension with countersunk heads, the tensile value shall be
A. Reduced by 25 %
B. Reduced by 33.3%
C. Increased by 25 %
D. Increased by 33.3 %
Answer : B

21. Horizontal stiffener in a plate girder is provided to safeguard against
A. Shear buckling of web plate
B. Compression buckling of web plate
C. Yielding
D. All of the above
Answer : B

22. Effective sectional area of a compression member is:
A. Gross sectional area - area of rivet hole
B. Gross sectional area + area of rivet hole
C. Gross sectional area × area of rivet hole
D. Gross sectional area + area of rivet hole
Answer : A

23. A riveted joint many experience
A. Tearing failure of plates
B. Splitting failure of plates at the edges
C. Bearing failure of rivets
D. All the above
Answer : D

24. The external wind pressure acting on a roof depends on
A. Degree of permeability of roof
B. Slope of roof
C. Both (A) and (B)
D. None of the above
Answer : B

25. The deflection of beams may be decreased by
A. Increasing the depth of beam
B. Increasing the span
C. Decreasing the depth of beam
D. Increasing the width of beam
Answer : A

26. According to IS : 800-1962 the permissible bending stress in steel slab plates, is
A. 1500 kg/cm²
B. 1420 kg/cm²
C. 2125 kg/cm²
D. 1890 kg/cm²
Answer : D

27. When a tension member is made of four angles with a plate as a web, the allowance for holes is made as
A. Two holes for each angle and one hole for the web
B. One hole for each angle and one hole for the web
C. One hole for each angle and two holes for the web
D. Two holes for each angle and two holes for the web
Answer : C

28. Maximum pitch of rivets, used in steel stacks, is limited to
A. 6 t
B. 10 t
C. 12 t
D. 16 t Where t is thickness of thinner plate being connected
Answer : B

29. The channels get twisted symmetrically with regard to its axis
A. Parallel to flanges
B. Parallel to web
C. Perpendicular to flanges
D. Perpendicular to web
Answer : B

30. Net sectional area of a tension member, is equal to its gross section area
A. Plus the area of the rivet holes
B. Divided by the area of rivet holes
C. Multiplied by the area of the rivet holes
D. None of these
Answer : D

31. Slenderness ratio of a compression member is
A. Moment of inertia/Radius of gyration
B. Effective length/Area of cross-section
C. Radius of gyration/Effective length
D. Radius of gyration/ Area of cross-section
Answer : C

32. The ratio of longitudinal stress to strain within elastic limit, is known as
A. Modulus of elasticity
B. Shear modulus of elasticity
C. Bulk modulus of elasticity
D. All the above
Answer : A

33. As per IS : 800, for compression flange, the outstand of flange plates should not exceed
A. 12 t
B. 16 t
C. 20 t
D. 25 t Where t = thickness of thinnest flange plate
Answer : B

34. When plates are exposed to weather, tacking rivets are provided at a pitch in line not exceeding (where t is the thickness of the outside plate).
A. 8 t
B. 16 t
C. 24 t
D. 32 t
Answer : B

35. The diameter of base of conical flare of a steel stack is
A. Less than d
B. Equal to d
C. More than d
D. Any of the above Where d is the diameter of the cylindrical part
Answer : C

36. The average shear stress for rolled steel beam section, is
A. 845 kg/cm²
B. 945 kg/cm²
C. 1025 kg/cm²
D. 1500 kg/cm²
Answer : B

37. The heaviest I-section for same depth is
A. ISMB
B. ISLB
C. ISHB
D. ISWB
Answer : C

38. Design of a riveted joint, is based on the assumption:
A. Load is uniformly distributed among all the rivets
B. Shear stress on a rivet is uniformly distributed over its gross area
C. Bearing stress in the rivet is neglected
D. All the above
Answer : D

39. Pick up the correct statement from the following:
A. The slenderness ratio of lacing bars for compression members should not exceed 145
B. The minimum width of lacing bar connected with rivets of nominal diameter 16 mm, is kept 50 mm
C. The minimum thickness of a flat lacing bar is kept equal to onefortieth of its length between inner end rivets
D. All the above
Answer : D

40. If the thickness of plate to be connected by a rivet is 16 mm, then suitable size of rivet as per Unwin's formula will be
A. 16 mm
B. 20 mm C. 24 mm
D. 27 mm
Answer : C

41. Live load
A. Varies in magnitude
B. Varies in position
C. Is expressed as uniformly distributed load
D. All the above
Answer : D

42. The least dimension in case of a circular column of diameter D is taken as
A. 0.5 D
B. 0.68 D
C. 0.88 D
D. D
Answer : C

43. The main assumption of the method of simple design of steel frame work, is:
A. Beams are simply supported
B. All connections of beams, girders and trusses are virtually flexible
C. Members in compression are subjected to forces applied at appropriate eccentricities
D. All the above
Answer : D

44. Working shear stress on the gross area of a rivet as recommended by Indian Standards, is
A. 785 kg/cm²
B. 1025 kg/cm²
C. 2360 kg/cm²
D. None of these
Answer : B

45. The economical depth d of a web plate in which allowable bearing stress is f_b, and the maximum bending moment is M, as suggested by Rawater and Clark, is
A. d = ?(M/f_b)
B. d = 1.5 ?(M/f_b)
C. d = 2.5 ?(M/f_b)
D. d = 4.5 ?(M/f_b)
Answer : D

46. For a compression member with double angle section, which of the following section will give larger value of minimum radius of gyration?
A. Equal angles back to back
B. Unequal legged angles with long legs back to back
C. Unequal legged angles with short legs back to back
D. Both (B) and (C)
Answer : B

47. If L is the overall length of a combined footing having A as its area, d being the distance between the centre of gravity of the base and centre of the base, the larger width b is
A. (A/L) + (3Ad/L²)
B. (A/L) + (6Ad/L²)
C. (A/L) - (6Ad/L²)
D. (A/L) - (3Ad/L²)
Answer : B

48. In factory buildings, the horizontal beams spanning between the wall columns supporting a wall covering, are called
A. Stringers
B. Trimmers
C. Girts
D. Lintels
Answer : C

49. The greatest gauge of long rivets should not exceed (where d is the diameter of the holes).
A. 2 d
B. 4 d
C. 6 d
D. 8 d
Answer : D

50. The equivalent axial load may be defined as the load which produces a stress equal to
A. Maximum stress produced by the eccentric load
B. Maximum stressed fibre
C. Bending stress
D. None of these
Answer : A