RRB JE - Hydraulics & Fluid Machineries 1000+ MCQ [Solved] PDF Download

1. If a pump is handling water and is discharging a certain flow Q at a constant total dynamic head requiring a definite B.H.P., the same pump when handling a liquid of specific gravity 0.75 and viscosity nearly same as of water, the horse power required will be
A. Same
B. 0.75 B.H.P.
C. B.H.P./0.75
D. 1.5 B.H.P.
Answer : B

2. The unit speed of the turbine runner is
A. N/?H
B. N/H
C. N/H^3/2
D. N/H²
Answer : A

3. Francis turbine is best suited for
A. Medium head application from 24 to 180 m
B. Low head installation up to 30 m
C. High head installation above 180 m
D. All types of heads
Answer : A

4. Reciprocating pumps are no more to be seen in industrial applications (in comparison to centrifugal pumps) because of
A. High initial and maintenance cost
B. Lower discharge
C. Lower speed of operation
D. Necessity of air vessel
Answer : A

5. The overall efficiency for a Pelton wheel lies between
A. 0.50 to 0.65
B. 0.65 to 0.75
C. 0.75 to 0.85
D. 0.85 to 0.90
Answer : D

6. Multistage centrifugal pumps are used to obtain
A. High discharge
B. High head
C. Pumping of viscous fluids
D. High head and high discharge
Answer : B

7. Medium specific speed of a pump implies it is
A. Centrifugal pump
B. Mixed flow pump
C. Axial flow pump
D. Any one of the above
Answer : B

8. Power required to drive a centrifugal pump is directly proportional to ________ of its impeller.
A. Diameter
B. Square of diameter
C. Cube of diameter
D. Fourth power of diameter
Answer : D

9. Discharge of a centrifugal pump is
A. Directly proportional to diameter of its impeller
B. Inversely proportional to diameter of its impeller
C. Directly proportional to (diameter)² of its impeller
D. Inversely proportional to (diameter)² of its impeller
Answer : D

10. According to fan laws, for the fans having constant wheel diameters, the power demand varies
A. Directly as fan speed
B. Square of fan speed
C. Cube of fan speed
D. Square root of fan speed
Answer : C

11. The discharge through a turbine is
A. Directly proportional to H^1/2
B. Inversely proportional to H^1/2
C. Directly proportional to H^3/2
D. Inversely proportional to H^3/2
Answer : A

12. The speed ratio in case of Francis turbine varies from
A. 0.15 to 0.3
B. 0.4 to 0.5
C. 0.6 to 0.9
D. 1 to 1.5
Answer : C

13. By fitting an air vessel to the reciprocating pump, there is always a saving of work done and subsequently saving of power. This saving in case of a single acting reciprocating pump is
A. 39.2 %
B. 48.8 %
C. 84.8 %
D. 88.4 %
Answer : C

14. A Pelton wheel develops 1750 kW under a head of 100 metres while running at 200 r.p.m. and discharging 2500 litres of water per second. The unit discharge of wheel is
A. 0.25 m³/s
B. 0.5 m³/s
C. 1.5 m³/s
D. 2.5 m³/s
Answer : A

15. A jet of water is striking at the centre of a curved vane moving with a uniform velocity in the direction of jet. For the maximum efficiency, the vane velocity is ________ of the jet velocity
A. One-half
B. One-third
C. Two-third
D. Three-fourth
Answer : B

16. If the ratio's of the corresponding forces acting at corresponding points are equal, then the model and the prototype are said to have.
A. Geometric similarity
B. Kinematic similarity
C. Dynamic similarity
D. None of these
Answer : C

17. In axial flow fans and turbines, fluid enters and leaves as follows
A. Radially, axially
B. Axially, radially
C. Axially, axially
D. Radially, radially
Answer : C

18. The maximum number of jets generally employed in impulse turbine without jet interference is
A. 4
B. 6
C. 8
D. 12
Answer : B

19. The specific speed of a turbine is given by the equation
A. N?P / H^3/2
B. N?P / H²
C. N?P / H^5/4
D. N?P / H³
Answer : C

20. In a reaction turbine, the draft tube is used
A. To run the turbine full
B. To prevent air to enter the turbine
C. To increase the head of water by an amount equal to the height of the runner outlet above the tail race
D. To transport water to downstream
Answer : C

21. Multistage centrifugal pumps are used to
A. Give high discharge
B. Produce high heads
C. Pump viscous fluids
D. All of these
Answer : B

22. By fitting an air vessel to the reciprocating pump, there is always a saving of work done and subsequently saving of power. The saving in case of a double acting reciprocating pump is
A. 39.2 %
B. 48.8 %
C. 84.8 %
D. 88.4 %
Answer : A

23. Which of the following pump is suitable for small discharge and high heads?
A. Centrifugal pump
B. Axial flow pump
C. Mixed flow pump
D. Reciprocating pump
Answer : D

24. A hydraulic accumulator normally consists of
A. Two cylinders, two rams and a storage device
B. A cylinder and a ram
C. Two coaxial rams and two cylinders
D. A cylinder, a piston, storage tank and control valve
Answer : B

25. The efficiency of a hydraulic press is given by (where W = Weight lifted by ram, P = Force applied on plunger, A = Area of ram, and a = Area of plunger)
A. (W/p) × (A/a)
B. (p/W) × (a/A)
C. (W/p) × (a/A)
D. (p/W) × (A/a)
Answer : C

26. The runaway speed of a hydraulic turbine is the speed
A. At full load
B. At which there will be no damage to the runner
C. Corresponding to maximum overload permissible
D. At which the turbine will run freely without load
Answer : D

27. The unit power developed by a turbine is (where P = Power developed by the turbine under a head of water (H).
A. P/ ?H
B. P/ H
C. P/ H^3/2
D. P/ H²
Answer : C

28. The unit discharge through the turbine is
A. Q/?H
B. Q/H
C. Q/H^3/2
D. Q/H²
Answer : A

29. Air vessels in reciprocating pump are used to
A. Smoothen flow
B. Reduce acceleration to minimum
C. Increase pump efficiency
D. Save pump from cavitations
Answer : B

30. The Thomson's turbine is __________ reaction turbine.
A. An axial flow
B. An inward flow
C. An outward flow
D. A mixed flow
Answer : B

31. Axial flow pump is started with its delivery valve
A. Kept fully closed
B. Kept fully open
C. Irrespective of any position
D. Kept 50% open
Answer : B

32. In a Francis turbine runner, the numbers of blades are generally between
A. 2 to 4
B. 4 to 8
C. 8 to 16
D. 16 to 24
Answer : D

33. The specific speed of a turbine is the speed of an imaginary turbine, identical with the given turbine, which
A. Delivers unit discharge under unit head
B. Delivers unit discharge under unit speed
C. Develops unit power under unit head
D. Develops unit power under unit speed
Answer : C

34. The number of buckets on the periphery of a Pelton wheel is given by
A. (D/2d) + 5
B. (D/2d) + 10
C. (D/2d) + 15
D. (D/2d) + 20
Answer : C

35. High specific speed of turbine implies it is
A. Propeller turbine
B. Francis turbine
C. Impulse turbine
D. None of the above
Answer : A

36. The specific speed of a hydraulic turbine depends upon
A. Speed and power developed
B. Discharge and power developed
C. Speed and head of water
D. Speed, power developed and head of water
Answer : D

37. When a piping system is made up primarily of vertical lift and very little pipe friction, the pump characteristics should be
A. Horizontal
B. Nearly horizontal
C. Steep
D. First rise and then fall
Answer : C

38. The working of which of the following hydraulic units is based on Pascal's law?
A. Air lift pump
B. Jet pump
C. Hydraulic coupling
D. Hydraulic press
Answer : D

39. The specific speed from 160 to 500 r.p.m. of a centrifugal pump indicates that the pump is
A. Slow speed with radial flow at outlet
B. Medium speed with radial flow at outlet
C. High speed with radial flow at outlet
D. High speed with axial flow at outlet
Answer : D

40. The angle of taper on draft tube is
A. Greater than 15°
B. Greater than 8°
C. Greater than 5°
D. Less than 8°
Answer : D

41. The depth of the bucket for a Pelton wheel is generally ________ the diameter of jet.
A. Equal to
B. 1.2 times
C. 1.8 times
D. Double
Answer : B

42. Indicator diagram of a reciprocating pump is a graph between
A. Flow vs. swept volume
B. Pressure in cylinder vs. swept volume
C. Flow vs. speed
D. Pressure vs. speed
Answer : B

43. Pressure intensifier increases the pressure in proportion to
A. Ratio of diameters
B. Square of ratio of diameters
C. Inverse ratio of diameters
D. Square of inverse ratio of diameters
Answer : B

44. Which of the following statement is wrong?
A. The reaction turbines are used for low head and high discharge.
B. The angle of taper on draft tube is less than 8°.
C. An impulse turbine is generally fitted slightly above the tail race.
D. A Francis turbine is an impulse turbine.
Answer : D

45. Motion of a liquid in a volute casing of a centrifugal pump is an example of
A. Rotational flow
B. Radial
C. Forced spiral vortex flow
D. Spiral vortex flow
Answer : D

46. Which place in hydraulic turbine is most susceptible for cavitations?
A. Inlet of draft rube
B. Blade inlet
C. Guide blade
D. Penstock
Answer : A

47. In an inward flow reaction turbine
A. The water flows parallel to the axis of the wheel
B. The water enters at the centre of the wheel and then flows towards the outer periphery of the wheel
C. The water enters the wheel at the outer periphery and then flows towards the centre of the wheel
D. The flow of water is partly radial and partly axial
Answer : C

48. According to fan laws, for fans having constant wheel diameter, the pressure varies
A. Directly as fan speed
B. Square of fan speed
C. Cube of fan speed
D. Square root of fan speed
Answer : B

49. The efficiency of a Pelton wheel working under constant head ________ with the increase in power.
A. Remain same
B. Increases
C. Decreases
D. None of these
Answer : B

50. The overall efficiency of a reaction turbine is the ratio of
A. Power produced by the turbine to the energy actually supplied by the turbine
B. Actual work available at the turbine to the energy imparted to the wheel
C. Workdone on the wheel to the energy (or head of water) actually supplied to the turbine
D. None of the above
Answer : A