SSC JHT - Engineering Drawing 1000+ MCQ [Solved] PDF Download

1. Inserting blocks into a drawing file usually requires exacting placement. The drafter should insure that ________ is turned on.
A. O Snaps
B. Ortho
C. Grid
D. Dynamic Input
Answer : A

2. In an oblique drawing, equally spaced partial circles may be used to show this:
A. Symbolic thread pitch
B. Ellipses
C. Cavalier drawings
D. Projection points
Answer : A

3. This is a rounded exterior blend between surfaces:
A. Fillet
B. Round
C. Taper
D. Chamfer
Answer : B

4. The offset distance for the width (front to back) distance of the auxiliary view is the same distance of the ________ in the top view.
A. Width
B. Height
C. Length
D. None of the above
Answer : A

5. This type of section is limited by a break line:
A. Removed section
B. Revolved section
C. Broken-out section
D. Half section
Answer : C

6. This is an angled surface used on cylinders to make them easier to handle:
A. Fillet
B. Taper
C. Chamfer
D. Lug
Answer : C

7. Two-point perspective is also known as:
A. Two-view perspective
B. Regular perspective
C. Parallel perspective
D. Angular perspective
Answer : D

8. These plans, made by the steel fabricator, are assembly drawings for the steel structure:
A. Welding plans
B. Assembly plans
C. Construction plans
D. Erection plans
Answer : D

9. There should be a visible gap between the wall and the ________ line.
A. Dimension
B. Extension
C. Center
D. Leader
Answer : B

10. This is the bottom surface joining the sides of two adjacent threads:
A. Lead
B. Pitch
C. Crest
D. Root
Answer : D

11. Drawings created with commercial software are typically saved as:
A. Rapid prototypes
B. Electronic files
C. Draft drawings
D. Change orders
Answer : B

12. An accurate record of changes made to release drawings is tracked via this:
A. A revision block
B. The basic title form
C. Working drawings
D. Portable documents
Answer : A

13. The Conceptual Visual Style tool is located on the ________ toolbar.
A. Visual Styles
B. Modify
C. 3-D Modeling
D. All of the above
Answer : A

14. Once a drawing is determined to be complete, the title block is used to document the change from:
A. A draft to a finished drawing
B. A finished to a working drawing
C. An assembly to a finished drawing
D. A working drawing to a draft
Answer : A

15. The distance a screw thread advances axially in one turn is the:
A. Lead
B. Pitch
C. Turn
D. Crest
Answer : A

16. In oblique sketches, the most commonly used angles for receding lines are:
A. 15 or 30 degrees
B. 25 or 30 degrees
C. 30 or 45 degrees
D. 45 or 60 degrees
Answer : C

17. A line with a tapering width can be easily created by using the __________ tool.
A. Circle
B. Ellipse
C. Line
D. Polyline
Answer : D

18. One critical issue drafters need to pay close attention to is the ________.
A. Size of the sheet
B. Designer's intent
C. Scale factor
D. None of the above
Answer : B

19. This type of solid has two bases that are parallel equal polygons:
A. Pyramid
B. Prism
C. Cone
D. Torus
Answer : B

20. Using the Relative Polar Coordinate System to add a 3 inch line that is 45 degrees from the end point of the line created above the drafter would ________.
A. Type @3<45 and enter
B. Type 3 back slash and enter
C. Type 3 forward slash and enter
D. Type 3 and try to use the Dynamic Input readout to find the end point
Answer : A

21. In order to set drawing limits for a C size architectural drawing the drafter should set the limits to ________.
A. 0, 0 and 2, 9
B. 0, 0 and 17, 11
C. 0, 0 and 18, 24
D. 0, 0 and 34, 24
Answer : C

22. These weld symbols have no arrow-side or other-side significance:
A. Projection or seam weld
B. Back or backing weld
C. Surface or groove weld
D. Flash and upset weld
Answer : D

23. This is a conical-shaped recess around a hole, often used to receive a tapered screw head:
A. Boss
B. Spotface
C. Counterbore
D. Countersink
Answer : D

24. The text used on a typical detail sheet should be ________.
A. Placed horizontally
B. In bold text
C. In an architectural text style
D. None of the above
Answer : A

25. The first step in creating a traditional technical drawing is to ________.
A. Draw a series of guide lines
B. Set up the meter line
C. Align the paper so that it will be positioned square to the parallel bar
D. Sharpen the leads in the technical pens
Answer : C

26. Referring to the fractional inches to decimal inches to millimetre conversion chart on page 55 what is the equivalent mm measurement of 3/16 inch.
A. 1.906
B. 4.7625
C. 5.958
D. 14.6844
Answer : B

27. This type of structural steel drawing shows all dimensions necessary for fabrication:
A. Shop drawings
B. Design drawings
C. Weldment drawings
D. Application drawings
Answer : A

28. A ________ section allows the drafter to create a Cutting Plane line which is not in a straight line across the part.
A. Offset
B. Half
C. Whole
D. Broken out
Answer : A

29. When the receding lines are true length, and the projectors are at 45 degrees to the plane of projection, the oblique drawing is called this:
A. Cabinet projection
B. Cavalier projection
C. Axonometric projection
D. Isometric projection
Answer : B

30. On a floor plan the dashed line that appears approximately 24 outside the exterior wall represents the __________.
A. Sidewalk
B. Roof overhang
C. Plumbing drain lines
D. None of the above
Answer : B

31. 5.These items typically are not used in new designs, but are still common in high-power amplifiers:
A. Amplifier tubes
B. Electron tubes
C. Signal relays
D. Switches
Answer : B

32. When creating a block the drafter needs to pay particular attention to selecting a base point because it determines the ________.
A. Scale
B. Rotation angle
C. Insertion point
D. Color
Answer : C

33. In multi-view drawing it is common practice to include three views, the front, the top and the right side. If no dimensions are required on the right side view the drafter can ________.
A. Leave the view as is
B. Eliminate the view
C. Use the left view instead
D. None of the above
Answer : B

34. This is used to indicate that a surface is to be machined:
A. Finish mark
B. Machining mark
C. Roughness indicator
D. Coordinate mark
Answer : A

35. When using versions of Auto-CAD prior to Release 2006 it may be necessary to ________ a block in order to edit it.
A. Copy
B. Explode
C. Offset
D. None of the above
Answer : B

36. In order to create one solid model from two or more separate solid shapes the drafter will need to position them and then ________.
A. Use Union to join them
B. Use the Join command
C. Use the Add Parts tool
D. None of the above
Answer : A

37. Isometric drawings are often used by ________ to help illustrate complex designs.
A. Mechanical engineers
B. Piping drafters
C. Aerospace engineers
D. All of the above
Answer : D

38. This type of weld is the most common in structural steel fabrication:
A. Fillet weld
B. Beam weld
C. Rivet weld
D. Structural weld
Answer : A

39. The dimension text size is determined by what the architect deems necessary in __________.
A. Model space
B. Paper space
C. The Finished plot
D. The PDF file
Answer : C

40. These types of projectors converge at a vanishing point:
A. Perspective
B. Parallel
C. Orthographic
D. Oblique
Answer : A

41. By using a ________ section of a cylindrical mechanical part the drafter should be able to show only one view of the part.
A. Half
B. Whole
C. Revolved
D. Broken out
Answer : C

42. This type of projection is when projectors are parallel to each other, but is at an angle other than 90 degrees to the plane of projection:
A. Oblique projection
B. Perpendicular projection
C. Aesthetic projection
D. Angular projection
Answer : A

43. These types of pipes are generally connected with bell and spigot joints or flanged joints:
A. Soil and waste
B. Water and gas
C. Water and steam
D. Gas and soil
Answer : B

44. Placement of dimensions on a drawing is controlled by ________.
A. ANSI
B. The design engineer
C. Corporate drafting standards
D. All of the above
Answer : D

45. Lines of an isometric drawing that are not parallel to the isometric axes are called this:
A. Trimetric lines
B. Non-isometric lines
C. Multiview lines
D. Dimetric lines
Answer : B

46. When drawing a line using the relative coordinate system a line is created from ________.
A. 0, 0
B. The ending point of the last line
C. The beginning point of the last line
D. None of the above
Answer : B

47. This type of thread is a thread on the inside of a member:
A. Basic thread
B. External thread
C. Internal thread
D. Major diameter thread
Answer : C

48. This is the term for the range of tightness or looseness resulting from the allowances and tolerances in mating parts:
A. Limits
B. Fit
C. Specifications
D. Allowance
Answer : B

49. The organized and orderly approach to solving problems is known as the:
A. Engineering process
B. Design process
C. Aesthetic process
D. Functional process
Answer : B

50. This type of drawing shows two lines representing the pipe diameter:
A. Single-line
B. Double-line
C. Standard piping
D. Centerline piping
Answer : B