SSC JHT - Hydraulics & Fluid Machineries 1000+ MCQ [Solved] PDF Download

1. The water in a jet propelled boat is drawn through the openings facing the direction of motion of the boat. The efficiency of propulsion is given by
A. 2V/(v_r - v)
B. 2V/(v_r + v)
C. V/(v_r - v)
D. V/(v_r + v)
Answer : B

2. In a centrifugal pump casing, the flow of water leaving the
A. Radial
B. Axial
C. Centrifugal
D. Vortex
Answer : D

3. If the net positive suction head (NPSH) requirement for the pump is not satisfied, then
A. No flow will take place
B. Cavitation will be formed
C. Efficiency will be low
D. Excessive power will be consumed
Answer : B

4. Which of the following pump is generally used to pump highly viscous fluid?
A. Centrifugal pump
B. Reciprocating pump
C. Air lift pump
D. Screw pump
Answer : D

5. A hydraulic accumulator is a device used to store ________ energy which may be supplied to a machine later on.
A. Strain
B. Pressure
C. Kinetic
D. None of these
Answer : B

6. The unit speed of the turbine runner is
A. N/?H
B. N/H
C. N/H^3/2
D. N/H²
Answer : A

7. For starting an axial flow pump, its delivery valve should be
A. Closed
B. Open
C. Depends on starting condition and flow desired
D. Could be either open or closed
Answer : B

8. Runaway speed of a hydraulic turbine is
A. Full load speed
B. The speed at which turbine runner will be damaged
C. The speed if the turbine runner is allowed to revolve freely without load and with the wicket gates wide open
D. The speed corresponding to maximum overload permissible
Answer : C

9. The power developed by a turbine is (where H = Head of water under which the turbine is working)
A. Directly proportional to H^1/2
B. Inversely proportional to H^1/2
C. Directly proportional to H^3/2
D. Inversely proportional to H^3/2
Answer : C

10. Any change in load is adjusted by adjusting following parameter on turbine
A. Net head
B. Absolute velocity
C. Blade velocity
D. Flow
Answer : D

11. Puck up the wrong statement about centrifugal pump
A. Discharge a diameter
B. Head a speed²
C. Head a diameter
D. Power a speed?
Answer : A

12. In impulse Turbine, energy available at the inlet is in the form of
A. Potential Energy
B. Strain Energy
C. Kinetic energy
D. None of these
Answer : C

13. Multistage centrifugal pumps are used to obtain
A. High discharge
B. High head
C. Pumping of viscous fluids
D. High head and high discharge
Answer : B

14. When a piping system is made up primarily of vertical lift and very little pipe friction, the pump characteristics should be
A. Horizontal
B. Nearly horizontal
C. Steep
D. First rise and then fall
Answer : C

15. Reciprocating pumps are no more to be seen in industrial applications (in comparison to centrifugal pumps) because of
A. High initial and maintenance cost
B. Lower discharge
C. Lower speed of operation
D. Necessity of air vessel
Answer : A

16. Discharge of a centrifugal pump is (where N = Speed of the pump impeller)
A. Directly proportional to N
B. Inversely proportional to N
C. Directly proportional to N²
D. Inversely proportional to N²
Answer : A

17. Specific speed for reaction turbines ranges from
A. 0 to 4.5
B. 10 to 100
C. 80 to 200
D. 250 to 300
Answer : B

18. In a Kaplan turbine runner, the numbers of blades are generally between
A. 2 to 4
B. 4 to 8
C. 8 to 16
D. 16 to 24
Answer : B

19. In order to avoid cavitation in centrifugal pumps
A. The suction pressure should be high
B. The delivery pressure should be high
C. The suction pressure should be low
D. The delivery pressure should be low
Answer : A

20. Francis turbine is best suited for
A. Medium head application from 24 to 180 m
B. Low head installation up to 30 m
C. High head installation above 180 m
D. All types of heads
Answer : A

21. For 450 m head of water, _________ shall be used.
A. Pelton wheel
B. Kaplan turbine
C. Francis turbine
D. None of these
Answer : A

22. The overall efficiency for a Pelton wheel lies between
A. 0.50 to 0.65
B. 0.65 to 0.75
C. 0.75 to 0.85
D. 0.85 to 0.90
Answer : D

23. The specific speed of turbine is defined as the speed of a unit
A. Of such a size that it delivers unit discharge at unit head
B. Of such a size that it delivers unit discharge at unit power
C. Of such a size that it requires unit power per unit head
D. Of such a size that it produces unit horse power with unit head
Answer : D

24. The depth of the bucket for a Pelton wheel is generally ________ the diameter of jet.
A. Equal to
B. 1.2 times
C. 1.8 times
D. Double
Answer : B

25. Which of the following statement is wrong?
A. The reaction turbines are used for low head and high discharge.
B. The angle of taper on draft tube is less than 8°.
C. An impulse turbine is generally fitted slightly above the tail race.
D. A Francis turbine is an impulse turbine.
Answer : D

26. A turbine pump is basically a centrifugal pump equipped additionally with
A. Adjustable blades
B. Backward curved blades
C. Vaned diffusion casing
D. Inlet guide blades
Answer : C

27. The function of guide vanes in a reaction turbine is to
A. Allow the water to enter the runner without shock
B. Allow the water to flow over them, without forming eddies
C. Allow the required quantity of water to enter the turbine
D. All of the above
Answer : D

28. The power produced by the reaction turbine is ________ to the head of water.
A. Directly proportional
B. Inversely proportional
C. 4th power
D. None of these
Answer : A

29. The ratio of actual work available at the turbine to the energy imparted to the wheel is known as ________ efficiency.
A. Hydraulic
B. Mechanical
C. Overall
D. None of these
Answer : B

30. A Francis turbine is used when the available head of water is
A. 0 to 25 m
B. 25 m to 250 m
C. Above 250 m
D. None of these
Answer : B

31. Which of the following pump is preferred for flood control and irrigation applications?
A. Centrifugal pump
B. Axial flow pump
C. Mixed flow pump
D. Reciprocating pump
Answer : B

32. Overall efficiency of a centrifugal pump is the ratio of
A. Energy available at the impeller to the energy supplied to the pump by the prime mover
B. Actual workdone by the pump to the energy supplied to the pump by the prime mover
C. Energy supplied to the pump to the energy available at the impeller
D. Manometric head to the energy supplied by the impeller per kN of water
Answer : B

33. The hydraulic efficiency of an impulse turbine is maximum when velocity of wheel is _______ of the jet velocity,
A. One-fourth
B. One-half
C. Three-fourth
D. Double
Answer : B

34. One horsepower is equal to
A. 102 watts
B. 75 watts
C. 550 watts
D. 735 watts
Answer : D

35. Kinematic similarity is said to exist between the model and the prototype, if both of them
A. Have identical velocities
B. Are equal in size and shape
C. Are identical in shape, but differ only in size
D. Have identical forces
Answer : A

36. A hydraulic press is a device used
A. To store pressure energy which may be supplied to a machine later on
B. To increase the intensity of pressure of water by means of energy available from a large quantity of water at a low pressure
C. To lift larger load by the application of a comparatively much smaller force
D. All of the above
Answer : C

37. The centrifugal pump preferred for a specific speed between 80 to 160 r.p.m. is
A. Slow speed with radial flow at outlet
B. Medium speed with radial flow at outlet
C. High speed with radial flow at outlet
D. High speed with mixed flow at outlet
Answer : D

38. Impulse turbine is generally fitted
A. At the level of tail race
B. Little above the tail race
C. Slightly below the tail race
D. About 2.5 m above the tail race to avoid cavitations.
Answer : B

39. Which of the following hydraulic unit is used for transmitting increased or decreased torque to the driven shaft?
A. Hydraulic ram
B. Hydraulic intensifier
C. Hydraulic torque converter
D. Hydraulic accumulator
Answer : C

40. Air vessels in reciprocating pump are used to
A. Smoothen flow
B. Reduce acceleration to minimum
C. Increase pump efficiency
D. Save pump from cavitations
Answer : B

41. The undershot water wheels are those in which
A. The wheel runs entirely by the weight of water
B. The wheel runs entirely by the impulse of water
C. The wheel runs partly by the weight of water and partly by the impulse of water
D. None of the above
Answer : B

42. According to fan laws, at constant speed and capacity, the pressure and power vary
A. Directly as the air or gas density
B. Inversely as square root of density
C. Inversely as density
D. As square of density
Answer : A

43. Hydraulic accumulator is used for
A. Accumulating oil
B. Supplying large quantities of oil for very short duration
C. Generally high pressures to operate hydraulic machines
D. Supplying energy when main supply fails
Answer : D

44. High specific speed of turbine implies it is
A. Propeller turbine
B. Francis turbine
C. Impulse turbine
D. None of the above
Answer : A

45. Which of the following statement is correct as regard to water wheels?
A. They have slow speeds
B. They are suitable even for low water heads
C. They give constant efficiency, even if the discharge is not constant
D. All of the above
Answer : D

46. By fitting an air vessel to the reciprocating pump, there is always a saving of work done and subsequently saving of power. This saving in case of a single acting reciprocating pump is
A. 39.2 %
B. 48.8 %
C. 84.8 %
D. 88.4 %
Answer : C

47. Maximum impulse will be developed in hydraulic ram when
A. Waste valve closes suddenly
B. Supply pipe is long
C. Supply pipe is short
D. Ram chamber is large
Answer : A

48. A Pelton wheel develops 1750 kW under a head of 100 metres while running at 200 r.p.m. and discharging 2500 litres of water per second. The unit discharge of wheel is
A. 0.25 m³/s
B. 0.5 m³/s
C. 1.5 m³/s
D. 2.5 m³/s
Answer : A

49. The force exerted by a jet of water (in a direction normal to flow) impinging on a fixed plate inclined at an angle ? with the jet is
A. waV/2g × sin?
B. waV/g × sin?
C. waV²/2g × sin2?
D. waV²/g × sin?
Answer : C

50. The overall efficiency of a reaction turbine is the ratio of
A. Power produced by the turbine to the energy actually supplied by the turbine
B. Actual work available at the turbine to the energy imparted to the wheel
C. Workdone on the wheel to the energy (or head of water) actually supplied to the turbine
D. None of the above
Answer : A