Related Questions
What is the correct answer?
4
This is a conical-shaped recess around a hole, often used to receive a tapered screw head:
What is the correct answer?
4
Architectural dimensioning standards allow for the placement of dimensions inside the floor plan. These inside dimensions locate interior __________.
A. Door openings and walls
What is the correct answer?
4
The primary unit of measurement for engineering drawings and design in the mechanical industries is the:
What is the correct answer?
4
When positioning this feature of perspective projection, the centerline of the cone of visual rays should be directed toward the approximate center of the object:
What is the correct answer?
4
A cylinder can be created by drawing a rectangular shape then the ________ tool.
What is the correct answer?
4
This is the smallest diameter of a screw thread:
A. Internal thread diameter
D. External thread diameter
What is the correct answer?
4
Some traditional board drafters preferred the drafting machine over the parallel straight edge because it could be used without the need for________.
What is the correct answer?
4
It is customary for the first sheet of a working drawing set to include ________.
What is the correct answer?
4
The Offset tool should only be used for placing ________ in an isometric drawing.
What is the correct answer?
4
In the section view, the areas that would have been in actual contact with the cutting plane are shown with:
What is the correct answer?
4
Geometric primitives include shapes such as ________.
What is the correct answer?
4
In order to set drawing limits for a C size architectural drawing the drafter should set the limits to ________.
What is the correct answer?
4
In this type of view, the cutting plane line indicates both the location of the cutting plane and the direction of sight:
What is the correct answer?
4
How can the drafter prevent Auto-CAD from placing or stacking another center mark on a circle when adding a diameter dimension to it?
A. Explode the dimension and then erase the center mark
B. Use the Properties dialog box to turn off the center mark of the dimension
D. Use the trim tool to take away the stacked center mark
What is the correct answer?
4
The architectural and construction industries use the United States National CAD standard (NCS) system on many ________ projects.
What is the correct answer?
4
The UCS icon represents the intersection of the ________.
What is the correct answer?
4
A circular arc is dimensioned in the view where you see its true shape by giving the value for its:
What is the correct answer?
4
Architectural dimensioning is usually done in ________.
What is the correct answer?
4
Dimensions are used on the elevation plan to describe ________.
A. Finished floor elevations
What is the correct answer?
4
An advantage of this type of view is that each view shows the object all the way through as if it were transparent:
What is the correct answer?
4
A round is a rounded surface on the ________ corner of a part.
What is the correct answer?
4
If a plane is parallel to the plane of projection, it appears:
What is the correct answer?
4
The building construction industry relies on sets of ________ drawings to construct homes and commercial buildings.
What is the correct answer?
4
When drawing a line using the relative coordinate system a line is created from ________.
B. The ending point of the last line
C. The beginning point of the last line
What is the correct answer?
4
When creating an isometric drawing in Auto-CAD the drafter can utilize the Dynamic Input and Polar Coordinate system to place both vertical and horizontal lines. A line created from one point 3 inches at 180 degrees would be a ________ line.
What is the correct answer?
4
Several of the tools used in traditional drafting include the following:
A. Parallel straight edge
What is the correct answer?
4
In oblique projection, important shapes should be in this position relative to the viewing plane:
What is the correct answer?
4
In this type of projection, each of the axes has different ratios of foreshortening:
What is the correct answer?
4
This is the intersection of the ground plane with the picture plane:
What is the correct answer?
4
The text height for room names should be set to ________for a drawing that will be plotted to a scale of ¼ = 1'-0.