Related Questions
What is the correct answer?
4
Percentage reduction in area performing tensile test on cast iron may be of the order of
What is the correct answer?
4
A column of length (l) with both ends fixed may be considered as equivalent to a column of length __________ with both ends hinged.
What is the correct answer?
4
The work ratio of simple gas turbine cycle depends upon
A. Maximum cycle temperature
B. Minimum cycle temperature
What is the correct answer?
4
The hyperbolic process is governed by
What is the correct answer?
4
According to Avogadro's law
A. The product of the gas constant and the molecular mass of an ideal gas is constant
B. The sum of partial pressure of the mixture of two gases is sum of the two
C. Equal volumes of all gases, at the same temperature and pressure, contain equal number of molecules
What is the correct answer?
4
The point of contra flexure is a point where
A. Shear force changes sign
B. Shear force is maximum
C. Bending moment changes sign
D. Bending moment is maximum
What is the correct answer?
4
For the same compression ratio, the efficiency of dual combustion cycle is
A. Greater than Diesel cycle and less than Otto cycle
B. Less than Diesel cycle and greater than Otto cycle
C. Greater than Diesel cycle
D. Less than Diesel cycle
What is the correct answer?
4
The intensity of stress which causes unit strain is called
What is the correct answer?
4
The distance between the centres of the rivets in adjacent rows of zigzag riveted joint is known as
What is the correct answer?
4
If both Stirling and Carnot cycles operate within the same temperature limits, then efficiency of Stirling cycle as compared to Carnot cycle
D. Depends on other factors
What is the correct answer?
4
The ideal efficiency of a Brayton cycle with regeneration, with increase in pressure ratio will
D. Increase/decrease depending on application
What is the correct answer?
4
Reversed joule cycle is called
What is the correct answer?
4
Second law of thermodynamics defines
What is the correct answer?
4
Otto cycle efficiency is higher than Diesel cycle efficiency for the same compression ratio and heat input because in Otto cycle
A. Combustion is at constant volume
B. Expansion and compression are isentropic
C. Maximum temperature is higher
D. Heat rejection is lower
What is the correct answer?
4
In S. I. units, the value of the universal gas constant is
What is the correct answer?
4
Euler's formula holds good only for
C. Both short and long columns
What is the correct answer?
4
A close cycle gas turbine gives __________ efficiency as compared to an open cycle gas turbine.
What is the correct answer?
4
The entropy may be expressed as a function of
A. Pressure and temperature
B. Temperature and volume
What is the correct answer?
4
A tri-atomic molecule consists of __________ atoms.
What is the correct answer?
4
The value of cp/cv for air is
What is the correct answer?
4
The expansion ratio (r) is the ratio of (where v1 = Volume at the beginning of expansion, and v2 = Volume at the end of expansion)
What is the correct answer?
4
When coal is strongly heated continuously for 42 to 48 hours in the absence of air in a closed vessel, the process is known as __________ of fuel.
What is the correct answer?
4
In the below figure, the stress corresponding to point D is
What is the correct answer?
4
Which of the following cycles is not a reversible cycle?
What is the correct answer?
4
The relation between Young's modulus (E), shear modulus (C) and bulk modulus (K) is given by
What is the correct answer?
4
The value of gas constant (R) in S. I. units is
What is the correct answer?
4
The most probable velocity of the gas molecules is given by
What is the correct answer?
4
If Kh is the torque resisting capacity of a hollow shaft and Ks is that of a solid shaft, of the same material, length and weight. Then,
What is the correct answer?
4
The neutral axis of a transverse section of a beam passes through the centre of gravity of the section and is
B. In the horizontal plane
C. In the same plane in which the beam bends
D. At right angle to the plane in which the beam bends
What is the correct answer?
4
The maximum shear stress, in the given figure, is equal to __________ of the Mohr's circle.