A compound cylinder with inner radius 50 mm and outer radius 70 mm is made by shrinking one cylinder on to the other cylinder, the junction radius is 60 mm and the junction pressure is 1.1 N/mm². The maximum hoop stress developed in the inner cylinder is
3.6 N/mm² compression
3.6 N/mm² tension
7.2 N/mm² compression
7.2 N/mm² tension
Correct Answer :
C. 7.2 N/mm² compression
Related Questions
A hot short metal is
Brittle when cold
Brittle when hot
Brittle under all conditions
Ductile at high temperature
The helix angle for single helical gears ranges from
10° to 15°
15° to 20°
20° to 35°
35° to 50°
The flank of the tooth is the
Surface of the top of the tooth
Surface of the tooth above the pitch surface
Width of the tooth measured along the pitch circle
Surface of the tooth below the pitch surface
The ratio of circumferential stress to longitudinal stress in a thin cylinder subjected to an internal pressure is
½
1
2
4
In a belt drive, if the pulley diameter is doubled keeping the tension and belt width constant, then it will be necessary to
Increase the key length
Increase the key depth
Increase the key width
Decrease the key length
In leaf springs, the longest leaf is known as
Master leaf
Lower leaf
Upper leaf
None of these
Two shafts will have equal strength, if
Diameter of both the shafts is same
Angle of twist of both the shafts is same
Material of both the shafts is same
Twisting moment of both the shafts is same
Endurance limit or fatigue limit is the maximum stress that a member can withstand for an infinite number of load applications without failure when subjected to
Dynamic loading
Static loading
Combined static and dynamic loading
Completely reversed loading
A sliding bearing which can support steady loads without any relative motion between the journal and the bearing, is called
Hydrostatic lubricated bearing
Hydrodynamic lubricated bearing
Boundary lubricated bearing
Zero film bearing
The building up of worn and undersized parts, subjected to repeated loads by electroplating is
Best method
Extremely hazardous
Has no effect as regards fatigue strength
Cheapest method
The rolling contact bearings as compared to sliding contact bearings have
Low starting and low running friction except at very high speeds
Accuracy of shaft alignment
Small overall dimensions
All of the above
Applications in which stresses are encountered in one direction only uses following type of threads
Metric
Buttress
Acme
Square
The included angle for the British Association thread is
29°
55°
47.3°
60°
When spring index increases, the value of Wahl's stress factor
Increases linearly
Decreases linearly
Remains same
Increases exponentially
Cast iron pipes are mainly used
For conveying steam
In water and sewage systems
In pressure lubrication systems on prime movers
All of the above
When the length of the journal is equal to the diameter of the journal, then the bearing is said to be a
Short bearing
Long bearing
Medium bearing
Square bearing
According to maximum shear stress theory, the maximum shear stress in the shaft is
(1/2) × √(σ² + 4τ²)
√(σ² + 4τ²)
(1/2) × [σ + √(σ² + 4τ²)]
σ + √(σ² + 4τ²)
In the assembly of pulley, key and shaft
Pulley is made the weakest
Key is made the weakest
Key is made the strongest
All the three are designed for equal strength
Stress concentration is caused due to
Variation in properties of material from point to point in a member
Pitting at points or areas at which loads on a member are applied
Abrupt change of section
All of the above
In a marine flange coupling, the thickness of flange is taken as
d/2
d/3
3d/4
d/4
In a full journal bearing, the angle of contact of the bearing with the journal is
120°
180°
270°
360°
In a gear, having Involute teeth, the normal to the Involute is a tangent to the
Base circle
Pitch circle
Addendum circle
Dedendum circle
The objective of crowning of the flat pulleys of belt drive is to
Prevent the belt from running off the pulley
Increase the power transmission capacity
Increase the belt velocity
Prevent the belt joint from damaging the belt surface
The bearings of medium series have capacity __________ over the light series.
10 to 20 %
20 to 30 %
30 to 40 %
40 to 50 %
Two shafts A and B under pure torsion are of identical length and identical weight and are made of the same material. The shaft A is solid and the shaft B is hollow. We can say that
Shaft B is better than shaft A
Shaft A is better than shaft B
Both the shafts are equally good
None of these
In order to determine the stresses in a thin cylinder due to an internal pressure, it is assumed that
The effect of curvature of the cylinder wall is neglected
The tensile stresses are uniformly distributed over the section of the walls
The effect of the restraining action of the heads at the end of the pressure vessel is neglected
All of the above
A steel containing upto 0.15% carbon is known as
Mild steel
Dead mild steel
Medium carbon steel
High carbon steel
In a marine flange coupling, the pitch circle diameter of bolts is taken as
1.2 d
1.6 d
2d
2.5 d
In a flange coupling, the flanges are coupled together by means of
Bolts and nuts
Studs
Headless taper bolts
None of these
According to I.B.R., the efficiency of a double riveted butt joint with double cover straps of equal width should be
45 to 60 %
63 to 70 %
70 to 83 %
80 to 90 %