Related Questions
What is the correct answer?
4
In S.H.M., the velocity vector w.r.t. displacement vector
What is the correct answer?
4
The relation between the controlling force (Fc) and radius of rotation (r) for a stable spring controlled governor is
What is the correct answer?
4
Which of the following statement is wrong?
A. The difference between the maximum and minimum energies is called maximum fluctuation of energy
B. The coefficient of fluctuation of speed is the ratio of maximum fluctuation of speed to the mean speed
C. The variations of energy above and below the mean resisting torque line is known as fluctuation of energy
What is the correct answer?
4
The motion between a pair which takes place in __________ is known as incompletely constrained motion.
C. More than one direction
What is the correct answer?
4
A mechanism is an assemblage of
C. Four or more than four links
What is the correct answer?
4
The coriolis component of acceleration leads the sliding velocity by
What is the correct answer?
4
Length of arc of contact is given by
A. Arc of approach - Arc of recess
B. Arc of approach + Arc of recess
C. Arc of approach / Arc of recess
D. Arc of approach × Arc of recess
What is the correct answer?
4
A disc is a spinning with an angular velocity ω rad/s about the axis of spin. The couple applied to the disc causing precession will be (where I = Mass moment of inertia of the disc, and ωP = Angular velocity of precession of the axis of spin)
What is the correct answer?
4
In its simplest form, a cam mechanism consists of following number of links
What is the correct answer?
4
The tractive force in a locomotive with two cylinders is given by (where c = Fraction of reciprocating parts per cylinder, m = Mass of reciprocating parts, ω = Angular speed of crank, r = Radius of crank, and θ = Angle of inclination of crank to the line of stroke)
C. (1 - c).m.ω².r (cosθ - sinθ)
What is the correct answer?
4
The ratio of the driving tensions for V-belts is __________ times that of flat belts. (Where β = Semi-angle of the groove)
What is the correct answer?
4
The critical speed of a shaft depends upon its
D. Stiffness and eccentricity
What is the correct answer?
4
In a mechanism, the fixed instantaneous centres are those centres which
A. Remain in the same place for all configurations of the mechanism
B. Vary with the configuration of the mechanism
C. Moves as the mechanism moves, but joints are of permanent nature
What is the correct answer?
4
In Meyer's expansion valve, the expansion valve is driven by an eccentric having an angle of advance from
What is the correct answer?
4
The direction of Coriolis component of acceleration is the direction
A. Of relative velocity vector for the two coincident points rotated by 90° in the direction of the angular velocity of the rotation of the link
B. Along the centripetal acceleration
C. Along tangential acceleration
D. Along perpendicular to angular velocity
What is the correct answer?
4
The type of gears used to connect two non parallel and non intersecting shafts is
What is the correct answer?
4
Shaft revolving in a bearing is the following type of pair
What is the correct answer?
4
A body will begin to move down an inclined plane, if the angle of inclination of the plane is ________ the angle of friction.
What is the correct answer?
4
The minimum periodic time of a compound pendulum is
What is the correct answer?
4
There are six gears A, B, C, D, E and F in a compound train. The numbers of teeth in the gears are 20, 60, 30, 80, 25 and 75 respectively. The ratio of angular speeds of the driven (F) to the driver (A) of the drive is
What is the correct answer?
4
With single Hooke's joint it is possible to connect two shafts, the axes of which have an angular misalignment up to
What is the correct answer?
4
The periodic time is given by (where ω = Angular velocity of the particle in rad/s)
What is the correct answer?
4
A system in dynamic balance implies that
A. The system is critically damped
B. There is no critical speed in the system
C. The system is also statically balanced
D. There will absolutely no wear of bearings
What is the correct answer?
4
A spring controlled governor is said to be unstable when the controlling force
A. Increases as the radius of rotation decreases
B. Increases as the radius of rotation increases
C. Decreases as the radius of rotation increases
D. Remains constant for all radii of rotation
What is the correct answer?
4
The brake commonly used in railway trains is
D. Internal expanding brake
What is the correct answer?
4
In a turning moment diagram, the variations of energy above and below the mean resisting torque line is called
B. Maximum fluctuation of energy
C. Coefficient of fluctuation of energy
What is the correct answer?
4
The absolute acceleration of any point P in a link about center of rotation O is
What is the correct answer?
4
A chain comprises of 5 links having 5 joints. Is it kinematic chain?
D. Data are insufficient to determine it
What is the correct answer?
4
The velocity of sliding of meshing gear teeth is (Where ω₁ and ω₂ are angular velocities of meshing gears and y is distance between point of contact and the pitch point)
What is the correct answer?
4
In which of the following type of gear train the first gear and the last gear are co-axial.