Home
Current Affairs January 2024

What is the correct answer?

4

A key capable of tilting in a recess milled out in a shaft is known as

A. Woodruff key

B. Feather key

C. Flat saddle key

D. Hollow saddle key

Correct Answer :

A. Woodruff key


Related Questions

What is the correct answer?

4

For high speed engines, the cam follower should move with

A. Uniform velocity

B. Simple harmonic motion

C. Uniform acceleration and retardation

D. Cycloidal motion

What is the correct answer?

4

Which of the following statement is correct regarding power screws?

A. The efficiency of a self locking screw can not be more than 50%

B. The efficiency of Acme (trapezoidal) thread is less than that of a square thread

C. If the friction angle is less than the helix angle of the screw, then the efficiency will be more than 50%

D. (A) and (B) Only

What is the correct answer?

4

The groove angle of pulleys for V-belt is

A. 340 to 360

B. 420 to 450

C. More than 400

D. 300 to 320

What is the correct answer?

4

When bevel gears connect two shafts whose axes intersect at an angle greater than a right angle and one of the bevel gears has a pitch angle of 90°, then they are known as

A. Angular bevel gears

B. Mitre gears

C. Internal bevel gears

D. Crown bevel gears

What is the correct answer?

4

Which one of the following loading is considered for the design of axles?

A. Bending moment only

B. Twisting moment only

C. Combined bending moment and twisting moments

D. Combined action of bending moment, twisting moment and axial thrust

What is the correct answer?

4

Which of the following statement is wrong?

A. A key is used as a temporary fastening

B. A key is subjected to tensile stresses

C. A key is always inserted parallel to the axis of the shaft

D. A key prevents relative motion between the shaft and boss of the pulley

What is the correct answer?

4

Stress concentration in static loading is more serious in

A. Ductile materials

B. Brittle materials

C. Equally serious in both cases

D. Depends on other factors

What is the correct answer?

4

During hot working of metals,

A. Porosity of the metal is largely eliminated

B. Grain structure of the metal is refined

C. Mechanical properties are improved due of refinement of grains

D. All of the above

What is the correct answer?

4

In designing a key, it is assumed that the distribution of forces along the length of key

A. Varies linearly

B. Is uniform throughout

C. Varies exponentially, being more at the torque-input end

D. Varies exponentially, being less at the torque-input end

What is the correct answer?

4

In a flange coupling, the bolts are subjected to

A. Tensile stress

B. Compressive stress

C. Shear stress

D. None of these

What is the correct answer?

4

The product of the diametral pitch and circular pitch is equal to

A. 1

B. 1/π

C. π

D. π × number of teeth

What is the correct answer?

4

A bolt of M 24 × 2 means that

A. The pitch of the thread is 24 mm and depth is 2 mm

B. Cross-sectional area of the threads is 24 mm²

C. The nominal diameter of bolt is 24 mm and pitch is 2 mm

D. The effective diameter of bolt is 24 mm and there are 2 threads per cm

What is the correct answer?

4

In a hydrodynamic lubricated bearing

A. There is a thick film of lubricant between the journal and the bearing

B. There is a thin film of lubricant between the journal and the bearing

C. The lubricant is forced between the journal and the bearing, by external pressure

D. There is no lubricant between the journal and the bearing

What is the correct answer?

4

The metal suitable for bearings subjected to heavy loads is

A. White metal

B. Silicon bronze

C. Monel metal

D. Phosphor bronze

What is the correct answer?

4

The efficiency of a square threaded screw is maximum if the helix angle is equal to (Where φ = Angle of friction)

A. 90° - φ

B. 45° - φ

C. 45° - φ/2

D. 45° + φ/2

What is the correct answer?

4

Rankine Gordon formula for buckling is valid for

A. Long column

B. Short column

C. Short and long column

D. Very long column

What is the correct answer?

4

Machine screws are

A. Similar to small size tap bolts except that a greater variety of shapes of heads are available

B. Slotted for a screw driver and generally used with a nut

C. Used to prevent relative motion between two parts

D. Similar to stud

What is the correct answer?

4

The expansion joint is mostly used for pipes which carry steam at __________ pressures.

A. Low

B. High

C. Medium

D. None of these

What is the correct answer?

4

A crankshaft is a __________ shaft.

A. Transmission

B. Machine

C. Machine frame

D. None of these

What is the correct answer?

4

The material commonly used for crane hooks is

A. Cast iron

B. Wrought iron

C. Mild steel

D. Aluminium

What is the correct answer?

4

The ratio of endurance limit in shear to the endurance limit in flexure is

A. 0.33

B. 0.4

C. 0.5

D. 0.55

What is the correct answer?

4

The power transmitted by the belt drive can be increased by

A. Increasing the initial tension in the belt

B. Dressing the belt to increase the coefficient of friction

C. Increasing wrap angle by using idler pulley

D. All of the above methods

What is the correct answer?

4

A plate with an elliptical hole in the centre, with semi-major axis (A) perpendicular to the direction of loading and semi-minor axis (b) along the direction of loading, is subjected to a pull P. The maximum stress induced at the edge of the hole is equal to (where σ = Stress for a plate with no hole i.e. nominal stress)

A. σ [1 + (b/2a)]

B. σ [1 + (2a/b)]

C. σ [1 + (b/3a)]

D. σ [1 + (3a/b)]

What is the correct answer?

4

For longitudinal joint in boilers, the type of joint used is

A. Butt joint with single cover plate

B. Butt joint with double cover plate

C. Lap joint with one ring overlapping the other

D. Any one of the above

What is the correct answer?

4

In case of thick cylinders, the tangential stress across the thickness of cylinder is

A. Maximum at the outer surface and minimum at the inner surface

B. Maximum at the inner surface and minimum at the outer surface

C. Maximum at the inner surface and zero at the outer surface

D. Maximum at the outer surface and zero at the inner surface

What is the correct answer?

4

The centre distance between two meshing involute gears is equal to

A. (Sum of base circle radii)/cosφ

B. (Difference of base circle radii)/cosφ

C. (Sum of pitch circle radii)/cosφ

D. (Difference of pitch circle radii)/cosφ

What is the correct answer?

4

The period during which the cam follower remains at rest, when cam moves, is known as

A. Constant period

B. Fixed period

C. Dwell period

D. Idle period

What is the correct answer?

4

In cylindrical cams, the follower moves

A. In a direction perpendicular to the cam axis

B. In a direction parallel to the cam axis

C. In any direction irrespective of cam axis

D. Along the cam axis

What is the correct answer?

4

A tapered key which fits in a key-way in the hub and is flat on the shaft, is known as

A. Woodruff key

B. Feather key

C. Flat saddle key

D. Gib head key

What is the correct answer?

4

When two springs are in series (having stiffness K), the equivalent stiffness will be

A. K

B. K/2

C. 2K

D. K/4