Related Questions
What is the correct answer?
4
Alloy powder manufactured by the following process have spherical shapes.
A. Electrochemical deposition
What is the correct answer?
4
A form of stress corrosion failure termed as 'season cracking' is generally observed in
A. Thermosetting polymers
What is the correct answer?
4
An abrupt and sudden fall in the reading of barometer is an indication of the
What is the correct answer?
4
Bad odour in sanitary latrines is reduced by periodically sprinkling
What is the correct answer?
4
The normal stress is the same in all directions at a point in a fluid, only when the fluid
A. Is at rest & has zero viscosity
C. Fluid layer has no motion relative to an adjacent layer of fluid
D. is incompressible & frictionless
What is the correct answer?
4
Maximum change in the hardness of martensite occurs in the carbon content range of __________ percent in steel.
What is the correct answer?
4
The value of for air & most common gases can be safely assumed to be
What is the correct answer?
4
The specific gravity of coal depends mainly on its __________ content.
What is the correct answer?
4
The difference in one unit of Rockwell hardness number corresponds to a difference in the depth of indentation of __________ mm.
What is the correct answer?
4
Air-petrol ratio for maximum power generation in spark ignition engine is about
What is the correct answer?
4
Pick out the correct combination about the role of various additives used in polymers.
A. Plasticiser: increases the polymer strength
B. Heat stabiliser: increases the maximum service temperature
C. Fillers: Does not affect the property of polymer but increases its weight
D. Lubricants: increases the flexibility of polymers
What is the correct answer?
4
Steel containing low percentage of nickel, chromium & tungsten are termed as the __________ steel.
What is the correct answer?
4
Which of the following has the highest value of refractive index?
What is the correct answer?
4
Ammonia leakage in the refrigeration system is detected by
A. Sulphur stick, which on detection gives white smoke
B. Using chemical reagents
What is the correct answer?
4
The dew point of moist air becomes __________ with decrease in its relative humidity.
A. Less than the wet bulb temperature
B. More than the wet bulb temperature
C. More than the dry bulb temperature
D. Equal to wet bulb temperature
What is the correct answer?
4
Heating the Hypo-eutectoid steels to 30°C above the upper critical temperature line, soaking at that temperature and then cooling slowly to the room temperature to form a pearlite & ferrite structure is called
What is the correct answer?
4
Percentage of argon (by volume) in dry atmospheric air is about
What is the correct answer?
4
Stainless steel is welded with difficulty because of
A. Its high melting temperature
D. Chromium carbide formation
What is the correct answer?
4
On oscilloscope screen for dynamic measurement, lissajous diagram is normally used to determine the __________ of the input signal.
What is the correct answer?
4
In the diving apparatus, helium is used along with oxygen, because it is
B. Not soluble in blood at high pressure
D. Completely miscible with oxygen
What is the correct answer?
4
A thin, flat & square plate measuring 2 m × 2 m is freely hanging in ambient air at 25°C. It is exposed to the solar radiation falling on one side of the plate at the rate of 500 W/m2. The plate temperature will remain constant at 30°C, if the convective heat transfer co-efficient is __________ W/m2 °C.
What is the correct answer?
4
Saturated steam at a pressure of 25 kg/cm2 is throttled to attain 5 kg/cm2. Then the outcoming steam will be
What is the correct answer?
4
Cementite is in the lamellar form in the __________ phase of steel.
What is the correct answer?
4
__________ is not a heat treatment process.
What is the correct answer?
4
Which one can be directly solidified from gaseous state without entering into liquid state?
What is the correct answer?
4
Pick out the wrong statement about the machinability of metals. Machinability of a metal
A. Decreases with increase in strain hardening tendencies
B. Decreases with increase in hardness, in general
C. Depend on the composition, microstructure and physical & mechanical properties
D. Decreases with increases in tensile strength & decrease in grain size
What is the correct answer?
4
A high pressure boiler generates steam at a pressure greater than __________ kg/cm2.
What is the correct answer?
4
The most commonly used moderator in nuclear power plants is
What is the correct answer?
4
Which of the following is not an ore of copper?
What is the correct answer?
4
Pick out the wrong statement.
A. Complete unity of command exists in a line organisation
B. Line organisation is net suitable for expansion and growth of an industry
C. In line and staff organisation, line executes and staff directs