A shaft is subjected to fluctuating loads for which the normal torque (T) and bending moment (M) are 1000 N-m and 500 N-m respectively. If the combined shock and fatigue factor for bending is 1.5 and combined shock and fatigue factor for torsion is 2, then the equivalent twisting moment for the shaft is
2000 N-m
2050 N-m
2100 N-m
2136 N-m
Correct Answer :
D. 2136 N-m
Related Questions
The rivet head used for boiler plate riveting is usually
Pan Head
Snap head
Counter sunk head
Conical head
A tapered key which fits in a key-way in the hub and is flat on the shaft, is known as
Woodruff key
Feather key
Flat saddle key
Gib head key
The strength of a riveted joint is equal to
Tearing strength of plate (Pt)
Shearing strength of rivet (Ps)
Crushing strength of rivet (Pc)
Least value of Pt Ps and Pc
The size of a gear is usually specified by
Pressure angle
Pitch circle diameter
Circular pitch
Diametral pitch
Maximum principal stress theory is applicable for
Ductile materials
Brittle materials
Elastic materials
All of the above
The velocity factor for precision metallic gears cut with high accuracy and operating at velocities upto 20 m/s is equal to
0.75/ (0.75 + √v)
3/ (3 + v)
4.5/ (4.5 + v)
6/ (6 + v)
In static loading, stress concentration is more serious in
Brittle materials
Ductile materials
Brittle as well as ductile materials
Elastic materials
A locking device in which the bottom cylindrical portion is recessed to receive the tip of the locking set screw, is called
Ring nut
Castle nut
Sawn nut
Jam nut
The belt slip occurs due to
Heavy load
Loose belt
Driving pulley too small
Any one of the above
For high speed engines, the cam follower should move with
Uniform velocity
Simple harmonic motion
Uniform acceleration and retardation
Cycloidal motion
Residual stress in materials
Acts when external load is applied
Becomes zero when external load is removed
Is independent of external loads
Is always harmful
The dedendum is the radial distance from the
Pitch circle to the top of a tooth
Pitch circle to the bottom of a tooth
Top of a tooth to the bottom of a tooth
Addendum circle to the clearance circle
The material commonly used for crane hooks is
Cast iron
Wrought iron
Mild steel
Aluminium
The number of slots in a 25 mm castle nut is
8
4
2
6
The application of third type levers is found in
Handle of a hand pump
Hand wheel of a punching press
Lever of a loaded safety valve
A pair of tongs
The included angle between the sides of V-belt is
40°
45°
38°
60°
A spring of stiffness 1000 N/m is stretched initially by 100 mm from the undeformed position. The work required to stretch it by another 100 mm is
5 N-m
7 N-m
10 N-m
15 N-m
In case of pressure vessels having open ends, the fluid pressure induces
Longitudinal stress
Circumferential stress
Shear stress
None of these
Slenderness ratio is the ratio of
Effective length of column to least radius of gyration of the column
Width of column to depth of column
Maximum size of column to minimum size of column
Effective length of column to width of column
According to I.B.R., the distance between the rows of rivets, for equal number of rivets in more than one row for lap joint or butt joint (chain riveting) shall not be less than
d
1.5 d
2d
2.5 d
A hollow saddle key is
A taper key which fits half in the key way of hub and half in the key way of shaft
A taper key which fits in a key way of the hub and is flat on the shaft
A taper key which fits in a key way of the hub and the bottom of the key is shaped to fit the curved surface of the shaft
Provided in pairs at right angles and each key is to withstand torsion in one direction only
According to Indian standard specifications, 100 H6/g5 means that
Tolerance grade for the hole is 6 and for the shaft is 5
Tolerance grade for the shaft is 6 and for the hole is 5
Tolerance grade for the shaft is 4 to 8 and for the hole is 3 to 7
Tolerance grade for the hole is 4 to 8 and for the shaft is 3 to 7
In case of thick cylinders, the tangential stress across the thickness of cylinder is
Maximum at the outer surface and minimum at the inner surface
Maximum at the inner surface and minimum at the outer surface
Maximum at the inner surface and zero at the outer surface
Maximum at the outer surface and zero at the inner surface
Which of the following statement is correct?
A parallel sunk key is a taperless key
A parallel sunk key may be rectangular or square in cross-section
A flat saddle key is a taper key which fits in a key way of the hub and is flat on the shaft
All of the above
The endurance or fatigue limit is defined as the maximum value of the stress which a polished standard specimen can withstand without failure, for infinite number of cycles, when subjected to
Static load
Dynamic load
Static as well as dynamic load
Completely reversed load
The permissible stress for carbon steel under static loading is generally taken as
2000-3000 kg/m²
3000-4000 kg/cm²
4000-4500 kg/cm²
7500-10,000 kg/cm²
When the connected members are very yielding (soft gasket) as compared to the bolt, then the resultant load on the bolt will be equal to the
Initial tension
External load applied
Sum of the initial tension and external load applied
Initial tension or external load, whichever is greater
Cap screws are
Similar to small size tap bolts except that a greater variety of shapes of heads are available
Slotted for a screw driver and generally used with a nut
Used to prevent relative motion between parts
Provided with detachable caps
An open coiled helical compression spring 'A' of mean diameter 50 mm is subjected to an axial load W. Another spring 'B' of mean diameter 25 mm is similar to spring 'A' in all respects. The deflection of spring 'B' will be __________ as compared to spring 'A'.
One-eighth
One-fourth
One-half
Double
A key made from a cylindrical disc having segmental cross-section, is known as
Woodruff key
Feather key
Flat saddle key
Gib head key