Related Questions
What is the correct answer?
4
When the wavelength of incident X-rays increases, the angle of diffraction
D. Shows no systematic variation
What is the correct answer?
4
In a good rimming steel
A. Carbon and silicon should be low
B. Silicon should be low but carbon should be high
C. Both silicon & carbon should be high
D. Silicon should be high but carbon should be low
What is the correct answer?
4
Projection welding & stud welding is categorised as the __________ welding.
What is the correct answer?
4
The difference between gross & net calorific values of fuel is due to the
A. Sensible heat carried away by the flue gases
B. Heat carried away by the steam from the moisture content of the fuel
C. Heat lost by radiation
D. Heat carried away by steam from the combustion of hydrogen in the fuel
What is the correct answer?
4
The substance used as a smoke screen in warfare is
What is the correct answer?
4
Moist air is cooled along the line of constant __________ , when it is passed over a cold & dry cooling coil, such that no condensation occurs?
What is the correct answer?
4
Case hardening of a material is
A. Followed by tempering or carburising
B. Preceded by its tempering
C. Done to get a soft ductile interior with a very hard surface
D. Carried out to get extreme hardness in its core
What is the correct answer?
4
Maximum hardenability of steel depends upon its
D. Alloying elements content
What is the correct answer?
4
Batch process is preferred over continuous process, when the
A. Product yields and quality cannot be achieved in continuous process, because of long residence time
B. Sales demand of product is not steady
C. Same equipment cannot be used for several processes of the same nature
What is the correct answer?
4
The behaviour of a metal specimen, which when plastically strained in tension reduces its yield stress in compression and vice versa; is termed as the
D. Stress recovery effect
What is the correct answer?
4
During sensible heating of humid air
A. Relative humidity increases
B. Dew point remains constant
C. Dry bulb & wet bulb temperature increases
What is the correct answer?
4
Upto the critical radius of insulation, added insulation, will
A. Increase the heat loss
B. Decrease heat loss and will have no effect beyond that
D. Reduce convection heat loss compared to conduction heat less
What is the correct answer?
4
Plasma is
A. A high temperature neutral gas
B. Nothing but ionised gas
C. A source of steady and highest controllable pressure
D. Formed at very low temperature
What is the correct answer?
4
Pick out the wrong statement
A. Processing of thermosetting plastics is ideally done by injection moulding
B. Processing of thermoplastics is ideally done by compression moulding
C. Mass production of seamless pipes are done by electrical resistance welding (ERW)
D. Stretch forming is a process of cold drawing
What is the correct answer?
4
Minimum temperature upto which water can be theoretically cooled down in the cooling tower by evaporative cooling is equal to the __________ temperature of air.
What is the correct answer?
4
Which one can be directly solidified from gaseous state without entering into liquid state?
What is the correct answer?
4
Which of the following low melting alloy containing bismuth and lead is used for electric fuse?
What is the correct answer?
4
In the formation of cermets, the ratio of ceramic material to metallic material is usually 80:20. Which of the following is a cermet?
What is the correct answer?
4
The elastic strain energy of a unit length of an edge dislocation as compared to that of a screw dislocation is
What is the correct answer?
4
The property of material, by which a given amount of energy is absorbed by it without plastic deformation, is called the
What is the correct answer?
4
When the wet steam is throttled but still remains wet at the exit of the throttle valve, then its temperature & dryness fraction respectively
What is the correct answer?
4
Which of the following hardness tests does not measure the indentation hardness of metals and alloys?
B. Shore scleroscope test
D. Rockwell hardness test
What is the correct answer?
4
__________ circuit is most commonly used to measure strain with the help of a strain gauge.
B. Voltage balancing potentiometric
C. Simple current sensitive
What is the correct answer?
4
A highly elastic material is deformed least on loading and retains its original form on removal of the load. Which of the following is the most elastic material?
What is the correct answer?
4
As per international norms, the maximum permissible value of noise level in the industrial environment is __________ decibels as measured at a distance of 1.5 metres from the source of noise.
What is the correct answer?
4
Which of the following parameters is not responsible for the heat loss from a hot steam carrying bare pipe surface located in a room without fans?
A. Emissivity of pipe surface
B. Diameter & length of the pipe
C. Temperature of hot pipe surface & that of air in the room
What is the correct answer?
4
Nitriding of a steel part does not increase its
What is the correct answer?
4
Air standard Otto cycle is more efficient than the diesel cycle for the same
A. Heat addition & compression ratio
B. Heat addition & pressure
C. Compression ratio & pressure
D. Cylinder dimension & rpm
What is the correct answer?
4
For infinite parallel planes having emissivities ε1 & ε2, the interchange factor for radiation from surface 1 to surface 2 is given by
What is the correct answer?
4
The material used for coating the welding electrode is termed as the