Related Questions
What is the correct answer?
4
A fluid is termed as the Newtonian fluid, when the shear stress is __________ the velocity gradient.
B. Inversely proportional to
C. Directly proportional to
What is the correct answer?
4
The capacity of a spring to store energy is called the spring form co-efficient. Stiffness of a spring is measured by the
A. Ability to absorb shock
B. Capacity to store energy
C. Ratio of the wire & coil diameters
D. Load to produce unit deflection
What is the correct answer?
4
Carnot cycle is also termed as the constant __________ cycle in thermodynamics.
What is the correct answer?
4
Quartz is a __________ material.
What is the correct answer?
4
Transition from laminar to turbulent zone in free convection heat transfer is governed by the critical value of
B. Grashoff number & Reynolds number
D. Grashoff number & Prandtl number
What is the correct answer?
4
Most important property of steels for use in automobile bodies is the
What is the correct answer?
4
Machinability of hard alloys and tool steels is improved by
What is the correct answer?
4
The difference between gross & net calorific values of fuel is due to the
A. Sensible heat carried away by the flue gases
B. Heat carried away by the steam from the moisture content of the fuel
C. Heat lost by radiation
D. Heat carried away by steam from the combustion of hydrogen in the fuel
What is the correct answer?
4
Which of the following is not an ore of copper?
What is the correct answer?
4
What is the value of entropy at 273°K?
What is the correct answer?
4
'Cryogenics' is concerned with the generation & use of low temperature in the range of
What is the correct answer?
4
Minimum number of members required to form a Public Limited Joint Stock Com-pany is
What is the correct answer?
4
The elastic strain energy of a unit length of an edge dislocation as compared to that of a screw dislocation is
What is the correct answer?
4
With increase in __________ Knocking tendency in a spark ignition petrol engine decreases.
What is the correct answer?
4
For a first order chemical reaction, the concentration of the reactant decreases __________ with time.
What is the correct answer?
4
The value of for air & most common gases can be safely assumed to be
What is the correct answer?
4
The stress at which extension of the material takes place more rapidly as compared to the increase in load is termed as the __________ point of the material.
What is the correct answer?
4
Mild steel has __________ crystal lattice structure.
A. Face centred cubic (fcc)
B. Body centred cubic (bcc)
What is the correct answer?
4
Out of the following __________ iron has the best capability to bear sudden & excessive shocks.
What is the correct answer?
4
__________ metal is used as a bearing liner material.
What is the correct answer?
4
__________ joint is usually used for joining cast iron pipes mostly used for temporary pipelines, where it may be necessary to dismantle & reassemble the pipeline very frequently.
What is the correct answer?
4
Energy of the sun arises mainly from __________ reactions.
What is the correct answer?
4
Maximum heat dissipation occurs from a steel wire (k = 0.5 W/m. k) of 15 mm diameter exposed to air (h = 20W/m2 .k), when the insulation thickness is __________ mm.
What is the correct answer?
4
Fatigue resistance of a material is measured by the
B. Ultimate tensile strength
What is the correct answer?
4
Electrolytic reduction cell used for conversion of calcined Al2O3 to Al is a carbon lined furnace operating at 800-900 °C. The purpose of electric current supplied to the furnace is to
A. Achieve very high purity of aluminium (99.9%)
B. Keep the electrolyte in liquid condition by the generation of heat
C. Electrolytically dissociate alumina
What is the correct answer?
4
Titanium is produced by __________ of Ti Cl4.
A. Electrolytic reduction
What is the correct answer?
4
Solute atoms which cause yield point phenomenon in mild steel are/is
What is the correct answer?
4
Which of the following emissions in the exhaust gas of an I.C. engine causes the formation of photochemical smog?
What is the correct answer?
4
Out of the following, the joint produced by __________ has the lowest strength.
What is the correct answer?
4
For a small scale toy factory, the fixed cost per month is Rs. 5000/-. The variable cost per toy is Rs. 20 and sales price is Rs. 30 per toy. The break even production per month will be __________ toys.