Home
Current Affairs January 2024

What is the correct answer?

4

Addition of __________ to steel does not help in improving its machinability.

A. Sulphur

B. Silicon

C. Lead

D. Phosphorous

Correct Answer :

B. Silicon


Related Questions

What is the correct answer?

4

In chemical dehumidification process

A. Wet bulb temperature increases

B. Dry bulb temperature remains constant

C. Dew point temperature increases

D. Dry bulb temperature increases

What is the correct answer?

4

Main constituent of bone ash is

A. Ammonium phosphate

B. Calcium phosphate

C. Animal charcoal

D. Ammonium sulphate

What is the correct answer?

4

The mechanism which changes the value of manipulated variable in response to the output signal from the control unit is called the

A. Final control element

B. On-off control

C. Floating control action

D. None of these

What is the correct answer?

4

Absolute zero pressure can be attained at a temperature of

A. 0°C

B. 50°K

C. 0°R

D. None of these

What is the correct answer?

4

Electrolytic reduction cell used for conversion of calcined Al2O3 to Al is a carbon lined furnace operating at 800-900 °C. The purpose of electric current supplied to the furnace is to

A. Achieve very high purity of aluminium (99.9%)

B. Keep the electrolyte in liquid condition by the generation of heat

C. Electrolytically dissociate alumina

D. Both (B) & (C)

What is the correct answer?

4

The burnout heat flux in the nucleate boiling regime is not a function of the

A. Liquid density

B. Vapour density

C. Temperature difference

D. Heat of evaporation

What is the correct answer?

4

Which of the, following is not associated with the functioning of a petrol engine?

A. Compression ignition system

B. Spark plug

C. Carburettor

D. Otto cycle

What is the correct answer?

4

Uniform ramming of sand in green sand moulding process leads to

A. Reduced chance of gas porosity

B. Greater dimensional stability of the casting

C. Uniform flow of molten metal into the mould cavity

D. Less sand expansion type of casting defect

What is the correct answer?

4

Production of one ton of paper in Indian paper industry consumes about __________ kWh of electricity.

A. 300

B. 800

C. 1400

D. 2000

What is the correct answer?

4

Co-efficient of performance of a Carnot cycle refrigerator operating between - 23°C and + 27°C is

A. 3

B. 5

C. 0.5

D. 1.5

What is the correct answer?

4

Pick out the wrong statement about the machinability of metals. Machinability of a metal

A. Decreases with increase in strain hardening tendencies

B. Decreases with increase in hardness, in general

C. Depend on the composition, microstructure and physical & mechanical properties

D. Decreases with increases in tensile strength & decrease in grain size

What is the correct answer?

4

Sacrificial anode method is used in the protection of pipelines which are buried underground. Sacrificial anode

A. Occurs higher in the electro-chemical series of metals

B. Is exemplified by magnesium plate

C. Is much cheaper than the cathodic base material to be guarded against corrosion

D. All (A), (B) & (C)

What is the correct answer?

4

Fog is an example of colloidal system of

A. Solid dispersed in gas

B. Solid dispersed in liquid

C. Liquid dispersed in gas

D. Gas dispersed in liquid

What is the correct answer?

4

Steam condenser tubes are made of admiralty brass, in which percentage of zinc & copper are __________ respectively.

A. 70 & 30

B. 30 & 70

C. 50 & 50

D. 90 & 10

What is the correct answer?

4

Venturimeter is used to measure the flow rate of fluids in pipes, when the pipe is in __________ position.

A. Horizontal

B. Vertical

C. Inclined

D. Any

What is the correct answer?

4

Hooke's law

A. Applies to elastic deformation

B. Applies beyond limit of proportionality in stress-strain curve

C. States that stress is inversely proportional to strain upto elastic limit

D. None of these

What is the correct answer?

4

The dew point of moist air becomes __________ with decrease in its relative humidity.

A. Less than the wet bulb temperature

B. More than the wet bulb temperature

C. More than the dry bulb temperature

D. Equal to wet bulb temperature

What is the correct answer?

4

Theoretical volume of oxygen required for complete combustion of 1Nm3 of acetylene, in oxyacetylene welding is __________ Nm3.

A. 0.5

B. 1

C. 1/3

D. 2.5

What is the correct answer?

4

Specific gravity of hot metal (pig iron) is __________ times that of the blast furnace slag.

A. 2

B. 3

C. 0.8

D. 6

What is the correct answer?

4

Mild steel has __________ crystal lattice structure.

A. Face centred cubic (fcc)

B. Body centred cubic (bcc)

C. Orthorhombic

D. Cubic

What is the correct answer?

4

Cemented carbide tools are not suitable for cutting

A. Aluminium

B. Brass

C. Cast iron

D. Steel

What is the correct answer?

4

To counteract the bad effects of strain hardening on a cold formed part, it must be

A. Tempered

B. Normalised

C. Annealed

D. Hardened

What is the correct answer?

4

Suitability of steel for its use in cable is judged by its strength in

A. Tension

B. Compression

C. Torsion

D. Shear

What is the correct answer?

4

Milk is fat dispersed in water. It is an example of

A. Suspension

B. Emulsion

C. Gel

D. Solution

What is the correct answer?

4

Pearlite comprises of

A. 87% cementite & 13% Fe

B. 87% ferrite & 13% cementite

C. 93.33% ferrite & 6.67% C

D. 87% ferrite & 13% C

What is the correct answer?

4

Temperature attained in soldering of metals is about __________ °C.

A. 150-300

B. 400-500

C. 650-800

D. 1000-1100

What is the correct answer?

4

The unit of gc is

A. lbm/lbf. ft/sec2

B. lbf/lbm. ft/sec2

C. ft/sec2

D. lbm/lbf. sec2/ft

What is the correct answer?

4

Diameter of the rivet to be provided on a 20 mm. thick boiler plate will be __________ mm.

A. 10

B. 20

C. 30

D. 40

What is the correct answer?

4

Powder metallurgy technique is used in the production of __________ tools.

A. Tungsten carbide

B. High carbon steel

C. High speed steel

D. Drilling

What is the correct answer?

4

Out of the following, the most malleable material is

A. Copper

B. Aluminium

C. Wrought iron

D. Lead