Related Questions
What is the correct answer?
4
Notched bar test is used for testing the __________ of a material.
What is the correct answer?
4
Pick out the wrong statement.
A. Complete unity of command exists in a line organisation
B. Line organisation is net suitable for expansion and growth of an industry
C. In line and staff organisation, line executes and staff directs
What is the correct answer?
4
What is the value of entropy at 273°K?
What is the correct answer?
4
Steel produced from phosphatic iron is __________ in nature.
What is the correct answer?
4
Fire refining process is employed in case of
What is the correct answer?
4
A high pressure boiler generates steam at a pressure greater than __________ kg/cm2.
What is the correct answer?
4
__________ temperature remains constant during adiabatic saturation process of unsaturated air.
What is the correct answer?
4
Which of the following heat treatment processes is usually applied to castings?
What is the correct answer?
4
Two wires of the same radius & material having length in the ratio of 1 : 2 are stretched by the same force. The strain produced in the two wires will be in the ratio of
What is the correct answer?
4
Cast iron contains __________ percent carbon.
What is the correct answer?
4
Pick out the wrong statement.
A. A soft magnetic material should have high permeability and small area of hysteresis loop
B. Poisson's ratio of high melting point metals is more than unity
C. Solders generally melt at less than 185°C
D. Steel produced by B.O.F process is ideally suited for manufacturing flat product
What is the correct answer?
4
Liquor poisoning generally occurs due to the presence of __________ in it.
What is the correct answer?
4
Which of the following is not used as a bearing material?
What is the correct answer?
4
Which of the following properties of a solid is not dependent on crystal imperfection?
What is the correct answer?
4
Aluminium is extracted from
What is the correct answer?
4
Larger length & diameter water pipes are made by
A. Electrical resistance welding
C. Semi-centrifugal casting
What is the correct answer?
4
'GASOHOL' widely used in Brazil as a motor fuel is a mixture of alcohol and
C. Light hydrocarbon gases (e.g. butane or propane)
What is the correct answer?
4
Pick out the wrong statement.
A. For a pressure vessel to be classified as 'thin vessel', the ratio of wall thickness to mean radius is less than 0.1
B. For calculating forces and efficiency of riveted joint, either rivet diameter or rivet hole diameter is used in case of pressure vessel and in structural work
C. Longitudinal joint is normally made butt joint to maintain the circularity of the vessel
D. Maximum diameter of the opening provided in a pressure vessel, which does not require any compensation is 200 mm
What is the correct answer?
4
Desalination of water
C. Means distillation of water
What is the correct answer?
4
Which of the following pairs is not correctly matched?
A. Uranium - 233 : Fertile material
B. Binding energy : Mass defect
C. Scattering: Absorption cross-section
D. Number of nucleons : Mass number
What is the correct answer?
4
The refractory brick which has good thermal shock resistance at high temperature but cracks on cooling below 400°C is
What is the correct answer?
4
Machinability of hard alloys and tool steels is improved by
What is the correct answer?
4
The minimum and the maximum number of members required to form a Private Limited Joint Stock Company are respectively
What is the correct answer?
4
Dry saturated steam can be converted into superheated steam by
A. Increasing its cross-sectional area of flow
B. Passing it through a pressure reducing valve
C. Forcing it downwards through a vertical tube
What is the correct answer?
4
Production of one ton of paper in Indian paper industry consumes about __________ kWh of electricity.
What is the correct answer?
4
__________ is the hardest oxide and is hence used where high wear resistance at high temperature is required.
What is the correct answer?
4
What is the critical radius of insulation (cms) for a metallic cylinder, if the convective heat transfer co-efficient with the ambient atmosphere is 5 W/m2. °K? Thermal conductivity of metal and insulation material are 40 and 0.1 W/m.°K respectively.
What is the correct answer?
4
The mechanism which changes the value of manipulated variable in response to the output signal from the control unit is called the
C. Floating control action
What is the correct answer?
4
The materials which fracture even at small strains are termed as brittle, while those materials which exhibit an appreciable deformation before failure are termed as
What is the correct answer?
4
In case of brasses, with decreasing zinc percentage and increasing copper percentage, its __________ increases.