Related Questions
What is the correct answer?
4
What is the value of included angle of a triangular notch for maximum discharge?
What is the correct answer?
4
In Imperial Smelting Process for extraction of zinc, zinc vapour thus produced is quenched in the external condenser by the use of the following:
A. Jet of water at high pressure
C. Mixture of water and air
What is the correct answer?
4
For a spontaneous natural process at constant temperature and pressure, the free energy of the system always
D. Increases to a maximum before decreasing
What is the correct answer?
4
The 'transition temperature' for ductile to brittle behaviour of steel increases with increase in the __________ content in steel.
What is the correct answer?
4
A highly elastic material is deformed least on loading and retains its original form on removal of the load. Which of the following is the most elastic material?
What is the correct answer?
4
Pearlite comprises of
A. 87% cementite & 13% Fe
B. 87% ferrite & 13% cementite
C. 93.33% ferrite & 6.67% C
What is the correct answer?
4
A material subjected __________ must have high resilience.
What is the correct answer?
4
Heating the Hypo-eutectoid steels to 30°C above the upper critical temperature line, soaking at that temperature and then cooling slowly to the room temperature to form a pearlite & ferrite structure is called
What is the correct answer?
4
The most prominent single cause of corrosion in boiler-tubes, drums, economisers and steam superheaters in a thermal power plant boiler is the
A. Water alkalinity & leakage
B. Hydrazine addition during feed water treatment
C. Release of non-condensable gas from water in the boiler
What is the correct answer?
4
__________ is used as a material of construction for the blade of power saw.
What is the correct answer?
4
__________ stress cannot be sustained by a fluid in equilibrium.
What is the correct answer?
4
Compressed dry air is used as the cutting fluid, while machining
What is the correct answer?
4
The activity of pure hydrogen gas at 1000°C and 5 atm pressure
B. Is always greater than 1
D. Depends on the choice of the standard state
What is the correct answer?
4
Hot & cold working of material causes its __________ deformation.
What is the correct answer?
4
Superheating of steam is done at constant
What is the correct answer?
4
Projection welding & stud welding is categorised as the __________ welding.
What is the correct answer?
4
Dielectric
A. Is an electrical insulating material
B. Of low resistivity is preferred
C. Should have high thermal conductivity
D. Need not defy the corrosive action of chemicals
What is the correct answer?
4
For separating small pieces of metal from engine oil of a car, the best separating technique is the
D. Fractional distillation
What is the correct answer?
4
With increase in temperature, the surface tension of water
What is the correct answer?
4
__________ wire is never used for making the heating element.
What is the correct answer?
4
The product (s) of roasting of a sulphide ore is (are)
D. Dependent on temperature and partial pressure of oxygen & sulphur dioxide
What is the correct answer?
4
Blasting of tri-nitro-toluene (TNT) is done by mixing it with ammonium
What is the correct answer?
4
The majority charge carriers in p-type silicon are
What is the correct answer?
4
Work done by a/an __________ process is determined by ∫p. dv
What is the correct answer?
4
Consider the equilibrium A(g) + B(g) = AB(g). When the partial pressure of A is 10-2 atm, the partial pressure of B is 10-3 atm and the partial pressure of AB is 1 atm, the equilibrium constant 'K' is
What is the correct answer?
4
Out of the following, which will fracture most readity, when hit with a hard hammer?
What is the correct answer?
4
Often earing defects are found during deep drawing operation, because the
A. Surface finish of the sheet is poor
B. Sheet material has been given substantial spring back
C. Starting sheet has planer anisotropy due to its texture
D. Starting sheet has normal anisotropy due to its texture
What is the correct answer?
4
While the recrystallisation temperature for pure metals is 0.3 Tm, the same for alloys is equal to __________ × Tm (where, Tm Melting temperature).
What is the correct answer?
4
Fatigue limit improvement by over stressing the metal by successively increasing the load is called coaxing. In fatigue failure, the material fails
C. Below the elastic limit
What is the correct answer?
4
Dew point temperature always gives an indication of the __________ of the moist air.