Related Questions
What is the correct answer?
4
Alumina, silica, lime and iron oxide are the basic raw material for the manufacture of Portland cement. The component of Portland cement which first hardens is
What is the correct answer?
4
Brass parts with high residual tensile stress at the surface are susceptible to season cracking (i.e. spontaneous cracking occuring on exposure to atmospheric corrosion), if its zinc percentage is more than
What is the correct answer?
4
The most economical channel section for the fluid flow is the one for which the discharge is maximum for a given cross-sectional area. Vertical velocity distribution in an open channel for laminar flow can be assumed to be
What is the correct answer?
4
__________ of hard alloy and tool steel is done to make it easily machinable.
What is the correct answer?
4
Name the safety device used to protect the boiler, when the water level falls below a minimum level.
What is the correct answer?
4
Saturated steam at a pressure of 25 kg/cm2 is throttled to attain 5 kg/cm2. Then the outcoming steam will be
What is the correct answer?
4
With increase in annealing temperature, the following defect density decreases.
What is the correct answer?
4
Which of the following is preferred for riveting?
What is the correct answer?
4
Fibrous fracture is normally encountered in the __________ materials.
What is the correct answer?
4
In a counter flow heat exchanger, hot fluid enters at 170°C & leaves at 150°C, while the cold fluid enters at 50°C & leaves at 70°C. The arithmetic mean temperature difference in this case is __________ °C.
What is the correct answer?
4
Which of the following metals reacts violently with water?
What is the correct answer?
4
Projection welding & stud welding is categorised as the __________ welding.
What is the correct answer?
4
Nitriding of a steel part does not increase its
What is the correct answer?
4
Annealing of white cast iron produces __________ iron.
What is the correct answer?
4
Cementite is in the lamellar form in the __________ phase of steel.
What is the correct answer?
4
Propulsion of rocket follows from the
A. Newton's second law of motion
B. Newton's third law of motion
What is the correct answer?
4
Corrosion of metals cannot be prevented by its
What is the correct answer?
4
Ganister contains maximum percentage of
What is the correct answer?
4
In a boundary layer developed along the flow, the pressure decreases in the downstream direction. The boundary layer thickness in this case will
What is the correct answer?
4
Blow off cock is provided in steam boiler to
A. Guard the boiler in case of abnormal rise in steam pressure
B. Drain out water and sludge during its repair
C. Regulate the supply of water in boiler
D. Put out the fire in the furnace when the water level in the boiler falls to unsafe limit
What is the correct answer?
4
Inertial forces are obtained, when the elastic forces are multiplied by __________ number.
What is the correct answer?
4
Ferromagnetic materials owe their properties to __________ inner sub-shells.
What is the correct answer?
4
Which of the following are made out of the carbon steel having carbon content of 0.9 to 1%?
A. Small punches, broaches reamers and springs
B. Cutlery, screws, rivets and files
C. Mandrels, twist drills, small lathe tools and razors
D. Forgings like can shaft, structural steel plate, threading dies and drawing dies
What is the correct answer?
4
Cast iron contains __________ percent carbon.
What is the correct answer?
4
Removal of non-condensable from steam or other vapour is termed as the __________ process.
What is the correct answer?
4
Silicon in steel
A. Makes it usable in almost all magnetic circuits where alternating current is used
B. Increases its electrical resistivity and decreases the hysteresis loss
C. Is present upto 5% & 4% respectively when used in transformers & motor armatures
What is the correct answer?
4
Energy of the sun arises mainly from __________ reactions.
What is the correct answer?
4
The property of material, by which a given amount of energy is absorbed by it without plastic deformation, is called the
What is the correct answer?
4
Reduction in the grain size reduces the __________ of the material.
What is the correct answer?
4
In extrusion of metals, which of the following statement is true?
A. Speed of the extruded material is same as that of ram speed
B. Redundant work is a function of the die angle
C. Relative motion between the billet surface and the container wall is always present
D. Hollow ram is used for indirect extrusion