Related Questions
What is the correct answer?
4
In multipass welds, shot peening is done after each pass to
A. Close the surface porosity
B. Break the continuity of columnar grains
D. Introduce texture in the weld
What is the correct answer?
4
Chlorine acts as a bleaching agent only in the presence of
What is the correct answer?
4
Rain drops falling through atmospheric air attain limited terminal velocity, because of
A. Upward thrust due to air
B. Viscous force exerted by air
C. Surface tension effects of water
What is the correct answer?
4
Absolute zero, pressure will occur, when the molecular momentum of the system becomes zero. A liquid will cease to exist as liquid at
What is the correct answer?
4
Cobalt - 60 is used as a source of __________ in medical therapy & industrial radiography.
What is the correct answer?
4
The atmospheric temperature during melting of ice/snow (in the atmosphere)
D. May increase or decrease; depends on the altitude where snow melts
What is the correct answer?
4
The emf of a Deniell cell Zn | Zn2+ || Cu2+ | Cu can be increased by
A. Decreasing the surface area of the electrodes
B. Increasing the concentration of zinc sulphate solution
C. Increasing the surface area of the electrodes
D. Increasing the concentration of copper sulphate solution
What is the correct answer?
4
Energy of the sun arises mainly from __________ reactions.
What is the correct answer?
4
Annealing of cast iron
A. Softens it to facilitate machining
B. Decreases the free carbon
C. Increases the strength
What is the correct answer?
4
Heat transfer to the water wall in a high pressure water wall type boiler furnace is mainly by
What is the correct answer?
4
Inertial forces are obtained, when the elastic forces are multiplied by __________ number.
What is the correct answer?
4
Thermal efficiency of an internal combustion engine is around __________ percent.
What is the correct answer?
4
As per international norms, the maximum permissible value of noise level in the industrial environment is __________ decibels as measured at a distance of 1.5 metres from the source of noise.
What is the correct answer?
4
In extrusion of metals, which of the following statement is true?
A. Speed of the extruded material is same as that of ram speed
B. Redundant work is a function of the die angle
C. Relative motion between the billet surface and the container wall is always present
D. Hollow ram is used for indirect extrusion
What is the correct answer?
4
Even though heat transfer co-efficient in boiling liquids is large, use of fins is advantageous, when the entire surface is exposed to __________ boiling.
What is the correct answer?
4
For preparation of porous bearings by powder metallurgy, preferred particle shape is
What is the correct answer?
4
Thermit welding is categorised as the __________ welding.
What is the correct answer?
4
A form of stress corrosion failure termed as 'season cracking' is generally observed in
A. Thermosetting polymers
What is the correct answer?
4
LVDT used for displacement measurement is a/an __________ transducer.
What is the correct answer?
4
Basicity of the slag in Indian blast furnace is in the range of
What is the correct answer?
4
Which of the following does not have a sharp melting point?
What is the correct answer?
4
__________ flux is used for the extraction of metal from its self fluxing ores.
What is the correct answer?
4
Surface tension of a liquid
A. Is due to intermolecular forces of cohesion
B. Decreases with rise in temperature
C. Is responsible for the spherical shape of an isolated liquid drop
What is the correct answer?
4
The refractory lining of the bottom in a basic electric arc furnace is made of
What is the correct answer?
4
Colour comparator is used to measure the
What is the correct answer?
4
Coating provided on the electrodes used in the arc welding is not expected to
B. Prevent electrode from contamination
D. Provide protective atmosphere to weld
What is the correct answer?
4
Specific __________ is a dimensionless quantity.
What is the correct answer?
4
__________ is the process of coating the surface of steel with aluminium oxide, thereby imparting it increased resistance to corrosion & oxidation upto a temperature of 700°C.
What is the correct answer?
4
Carbide tipped cutting tools are manufactured by powder metallurgy techniques and have a composition of
A. 90% tungsten carbide and 10% cobalt
B. 70% aluminium oxide & 30% silica
C. 30% nickel, 15% chromium & 55% tungsten
D. 65% tungsten & 35% zirconium
What is the correct answer?
4
Propulsion of rocket follows from the
A. Newton's second law of motion
B. Newton's third law of motion