Related Questions
What is the correct answer?
4
Architectural dimensioning standards allow for the placement of dimensions inside the floor plan. These inside dimensions locate interior __________.
A. Door openings and walls
What is the correct answer?
4
This type of circuit is a semiconductor wafer or chip:
What is the correct answer?
4
Perspective drawings are classified according to their number of these features:
What is the correct answer?
4
A secondary auxiliary view is a projection off of the ________.
C. Primary auxiliary view
What is the correct answer?
4
An architect often relies on a ________ to complete the set of technical drawings used in the design of an office building.
D. Construction superintendent
What is the correct answer?
4
Welding drawings are a special type of this kind of drawing:
What is the correct answer?
4
Referring to the fractional inches to decimal inches to millimetre conversion chart on page 55 what is the equivalent mm measurement of 3/16 inch.
What is the correct answer?
4
A round is a rounded surface on the ________ corner of a part.
What is the correct answer?
4
The offset distance for the width (front to back) distance of the auxiliary view is the same distance of the ________ in the top view.
What is the correct answer?
4
In this type of section, one quarter of the object is removed:
What is the correct answer?
4
In multi-view drawing it is common practice to include three views, the front, the top and the right side. If no dimensions are required on the right side view the drafter can ________.
C. Use the left view instead
What is the correct answer?
4
Switches and relays should be shown in this position with no operating force or applied energy:
What is the correct answer?
4
This type of solid has two bases that are parallel equal polygons:
What is the correct answer?
4
This is a curve showing the displacement of the follower as ordinates on a base line that represents one revolution of the cam:
What is the correct answer?
4
Oblique drawings are dimensioned in a similar fashion as these types of drawings:
What is the correct answer?
4
Center lines are used to locate or represent the centers of ________.
What is the correct answer?
4
In U.S. structural and architectural drafting, all dimensions of this length are usually expressed in feet and inches:
What is the correct answer?
4
When the drafter types the word BLOCK or selects the Make Block tool from the Draw tool bar the ________ will appear.
C. Block Definition Dialog
What is the correct answer?
4
Acceptable parts must not extend beyond this:
What is the correct answer?
4
Elevation drawings will include information about ________.
What is the correct answer?
4
This is the term for the range of tightness or looseness resulting from the allowances and tolerances in mating parts:
What is the correct answer?
4
Once a drawing is determined to be complete, the title block is used to document the change from:
A. A draft to a finished drawing
B. A finished to a working drawing
C. An assembly to a finished drawing
D. A working drawing to a draft
What is the correct answer?
4
This process recognizes the inherent interrelationships between design and manufacturing:
A. Design for manufacture
B. Design for manufacture and assembly
C. Design for concurrent engineering
What is the correct answer?
4
This type of surface is tipped to all principal planes of projection and does not appear true size in any standard view:
What is the correct answer?
4
These types of pipes are generally connected with bell and spigot joints or flanged joints:
What is the correct answer?
4
A partial auxiliary view is used to show only the ________ in the auxiliary view.
A. Projected inclined plane
B. The projected top view
C. The projected side view
What is the correct answer?
4
A civil engineer working on a bridge design would probably rely on his ________ scale for checking printed drawings.
What is the correct answer?
4
A ________ is the person responsible for verifying that the drawings in a project set are free of mistakes.
What is the correct answer?
4
These drawings are given to contractors to perform work or manufacture individual parts:
What is the correct answer?
4
When using the descriptive geometry method to create an auxiliary view the drafter should __________.
A. Rotate the snap grid to the same angle of the inclined plane
B. Offset the right vertical line of the front view
C. Rotate the top line of the front view 45 degrees
D. Offset the top line of the front view 2 inches