An example of unsteady non uniform flow is the flow of liquid under pressure through a

Question

An example of unsteady non uniform flow is the flow of liquid under pressure through a

A. Tapering pipe at constant flow rate

B. Tapering pipe at either decreasing or increasing flow rate

C. Long pipeline of constant diameter

D. None of these

Share this question with your friends

Show all Chemical Engineering Basics MCQ

Comment

Runge-Kutta method is used to solve a/an

A. Ordinary differential equation of nth order

B. Simultaneous non-linear equation

C. Linear differential equation

D. None of these

Discuss this answer

Electrochemical corrosion can occur, only if __________ is present in contact with metal.

A. Air

B. Oxygen

C. Liquid medium

D. Gaseous medium

Discuss this answer

The yield point phenomenon observed in annealed low carbon steel is due to the presence of the following element.

A. Silicon

B. Carbon

C. Phosphorous

D. Chromium

Discuss this answer

'Dikes' are low height walls made around the storage vessels meant for storing hazardous & inflammable material (e.g., petroleum products). Volume of dikes is equal to (where, V = volume of the storage vessel)

A. V

B. V/2

C. 2V

D. 3V

Discuss this answer

As the fluid flow rate increases, the float of the Rotameter

A. Rises in the tube

B. Rotates at higher speed

C. Rotates at lower speed

D. Drops down in the tube

Discuss this answer

Wavelength of radiation emitted by a body depends on the __________ of its surface.

A. Temperature

B. Area

C. Nature

D. All 'a', 'b' & 'c'

Discuss this answer

Tumbling is the process of improving the __________ of the materials/parts.

A. Surface finish

B. Fatigue limit

C. Creep limit

D. Surface cleanliness

Discuss this answer

Production of one ton of paper in Indian paper industry consumes about __________ kWh of electricity.

A. 300

B. 800

C. 1400

D. 2000

Discuss this answer

Lead is poured into the joint between two __________ pipes.

A. Mild steel

B. Concrete

C. Cast iron

D. Asbestos cement

Discuss this answer

Which of the following test is used for distinguishing among dry oils, semi-drying oils and non drying oils?

A. Elaiden test

B. Reichert-Meissl value test

C. Hunter value test

D. Iodine value test

Discuss this answer

Boiler draught of 10 mm water column is equivalent to

A. 1 kgf/m²

B. 10 kgf/m²

C. 10 kgf/mm²

D. 1 kgf/mm²

Discuss this answer

The most commonly used moderator in nuclear power plants is

A. Graphite

B. Light water

C. Heavy water

D. Beryllium

Discuss this answer

Otto cycle used in spark ignition petrol engines is also known as the constant __________ cycle.

A. Volume

B. Pressure

C. Heat

D. None of these

Discuss this answer

Heat release during phase change is observed in case of a/an

A. Boiler

B. Condenser

C. Evaporator

D. All (A), (B) & (C)

Discuss this answer

Brinell Hardness Number (BHN) for talc is approximately in the range of

A. 1-5

B. 20-30

C. 100-150

D. 200-250

Discuss this answer

Which of the following is an undesirable property of slag produced during the Pyrometallurgical method of metal extraction from its ore?

A. High fusibility & fluidity

B. High thermal conductivity

C. Low density

D. High chemical activity

Discuss this answer

Fibre reinforced plastic (FRP) are

A. Made of glass fibre and thermoplastic resins

B. Anisotropic

C. Made of thermosetting resin and glass fibre

D. Both 'b' & 'c'

Discuss this answer

Elimination of brittleness resulting from welding of saw blades is done by __________ of the welded portion.

A. Annealing

B. Toughening

C. Work hardening

D. Tempering

Discuss this answer

Which of the following metals cannot be hot worked at room temperature?

A. Zinc

B. Nickel

C. Lead

D. Tin

Discuss this answer

The heat of neutralisation remains constant, when there is a reaction between dilute solutions of strong

A. Base and strong acid

B. Base and weak acid

C. Acid and weak base

D. None of these

Discuss this answer

There are one octahedral void and __________ tetrahedral void in the closest packing of atoms.

A. One

B. Two

C. Three

D. None of these

Discuss this answer

The ratio of the shear stress to the principal stress on a principal plane is

A. 0

B. 1

C. 1/2

D. 1/3

Discuss this answer

Corona discharge is related to the operation of a/an

A. Induction motor

B. Electrostatic precipitator

C. Fast breeder reactor

D. Magneto hydrodynamic generator (MHD)

Discuss this answer

Fog is an example of colloidal system of

A. Solid dispersed in gas

B. Solid dispersed in liquid

C. Liquid dispersed in gas

D. Gas dispersed in liquid

Discuss this answer

Projection welding & stud welding is categorised as the __________ welding.

A. Pressure

B. Thermit

C. Resistance

D. Arc

Discuss this answer

Out of the following __________ iron has the best capability to bear sudden & excessive shocks.

A. White

B. Cast

C. Wrought

D. Pig

Discuss this answer

As per the Indian boiler regulation (IBR), the type of joint preferred for the circumferential joint is the __________ joint.

A. Butt

B. Lap

C. Welded

D. None of these

Discuss this answer

Electrometallurgy is not involved in the extraction of __________ from its ore.

A. Aluminium

B. Tin

C. Lead

D. Both (B) & (C)

Discuss this answer

Globular form of cementite is formed during the __________ process.

A. Spheroidising

B. Hardening

C. Annealing

D. Normalising

Discuss this answer

Pressure exerted by a liquid depends upon its

A. Surface tension

B. Density

C. Viscosity

D. Buoyancy

Discuss this answer

Accepted Answer

B. Tapering pipe at either decreasing or increasing flow rate

An example of unsteady non uniform flow is the flow of liquid under pressure through a

Correct Answer :

Show all Chemical Engineering Basics MCQ

Related Questions

Runge-Kutta method is used to solve a/an

Electrochemical corrosion can occur, only if __________ is present in contact with metal.

The yield point phenomenon observed in annealed low carbon steel is due to the presence of the following element.

'Dikes' are low height walls made around the storage vessels meant for storing hazardous & inflammable material (e.g., petroleum products). Volume of dikes is equal to (where, V = volume of the storage vessel)

As the fluid flow rate increases, the float of the Rotameter

Wavelength of radiation emitted by a body depends on the __________ of its surface.

Tumbling is the process of improving the __________ of the materials/parts.

Production of one ton of paper in Indian paper industry consumes about __________ kWh of electricity.

Lead is poured into the joint between two __________ pipes.

Which of the following test is used for distinguishing among dry oils, semi-drying oils and non drying oils?

Boiler draught of 10 mm water column is equivalent to

The most commonly used moderator in nuclear power plants is

Otto cycle used in spark ignition petrol engines is also known as the constant __________ cycle.

Heat release during phase change is observed in case of a/an

Brinell Hardness Number (BHN) for talc is approximately in the range of

Which of the following is an undesirable property of slag produced during the Pyrometallurgical method of metal extraction from its ore?

Fibre reinforced plastic (FRP) are

Elimination of brittleness resulting from welding of saw blades is done by __________ of the welded portion.

Which of the following metals cannot be hot worked at room temperature?

The heat of neutralisation remains constant, when there is a reaction between dilute solutions of strong

There are one octahedral void and __________ tetrahedral void in the closest packing of atoms.

The ratio of the shear stress to the principal stress on a principal plane is

Corona discharge is related to the operation of a/an

Fog is an example of colloidal system of

Projection welding & stud welding is categorised as the __________ welding.

Out of the following __________ iron has the best capability to bear sudden & excessive shocks.

As per the Indian boiler regulation (IBR), the type of joint preferred for the circumferential joint is the __________ joint.

Electrometallurgy is not involved in the extraction of __________ from its ore.

Globular form of cementite is formed during the __________ process.

Pressure exerted by a liquid depends upon its

Also checkout