Home
Current Affairs January 2024

What is the correct answer?

4

An Involute pinion and gear are in mesh. If both have the same size of addendum, then there will be interference between the

A. Tip of the pinion and flank of gear

B. Tip of the gear and flank of pinion

C. Flanks of both gear and pinion

D. Tip of both gear and pinion

Correct Answer :

B. Tip of the gear and flank of pinion


Related Questions

What is the correct answer?

4

A type of brake commonly used in motor cars is a

A. Shoe brake

B. Band and block brake

C. Band brake

D. Internal expanding brake

What is the correct answer?

4

In a flange coupling, the flanges are coupled together by means of

A. Bolts and nuts

B. Studs

C. Headless taper bolts

D. None of these

What is the correct answer?

4

The piston pin bearings in heavy duty diesel engines are

A. Needle roller bearings

B. Tapered roller bearings

C. Spherical roller bearings

D. Cylindrical roller bearings

What is the correct answer?

4

A key capable of tilting in a recess milled out in a shaft is known as

A. Woodruff key

B. Feather key

C. Flat saddle key

D. Hollow saddle key

What is the correct answer?

4

In composite or reverse laid ropes

A. Direction of twist of wires in strands is opposite to the direction of twist of strands

B. Direction of twist of wires and strands are same

C. Wires in two adjacent strands are twisted in opposite direction

D. Wires are not twisted

What is the correct answer?

4

According to Indian standard specifications, 100 H6/g5 means that

A. Tolerance grade for the hole is 6 and for the shaft is 5

B. Tolerance grade for the shaft is 6 and for the hole is 5

C. Tolerance grade for the shaft is 4 to 8 and for the hole is 3 to 7

D. Tolerance grade for the hole is 4 to 8 and for the shaft is 3 to 7

What is the correct answer?

4

The material generally used for aircraft components is

A. Mild steel

B. High speed steel

C. Stainless steel

D. Aluminium

What is the correct answer?

4

Multiple threads are used to secure

A. Low efficiency

B. High efficiency

C. High load lifting capacity

D. High mechanical advantage

What is the correct answer?

4

If the centre distance of the mating gears having involute teeth is varied within limits, the velocity ratio.

A. Increases

B. Decreases

C. Remains unchanged

D. None of these

What is the correct answer?

4

The groove angle of pulleys for V-belt is

A. 340 to 360

B. 420 to 450

C. More than 400

D. 300 to 320

What is the correct answer?

4

According to I.B.R., shearing resistance required to shear off the rivet per pitch length (in double shear) is (where n = Number of rivets per pitch length)

A. (π/4) d² × τ × n

B. 1.875 × (π/4) d² × τ × n

C. 2 × (π/4) d² × τ × n

D. 3 × (π/4) d² × τ × n

What is the correct answer?

4

When spring index increases, the value of Wahl's stress factor

A. Increases linearly

B. Decreases linearly

C. Remains same

D. Increases exponentially

What is the correct answer?

4

In an oil lubricated journal bearing, the coefficient of friction between the journal and the bearing

A. Remains constant at all speeds

B. Is minimum at zero speed and increases monotonically with increase in speed

C. Is maximum at zero speed and decreases monotonically with increase in speed

D. Becomes minimum at an optimum speed and then increases with further increase in speed

What is the correct answer?

4

The shear stress in a beam varies from zero at the outer fibres to a maximum at the________.

A. Neutral surface

B. Upper surface

C. Lower surface

D. None of these

What is the correct answer?

4

The designation M 33 × 2 of a bolt means

A. Metric threads of 33 numbers in 2 cm

B. Metric threads with cross-section of 33 mm

C. Metric threads of 33 mm outside diameter and 2 mm pitch

D. Bolt of 33 mm nominal diameter having 2 threads per cm

What is the correct answer?

4

The plasticity is the property of a material which enables it to

A. Regain its original shape after deformation when the external forces are removed

B. Draw into wires by the application of a tensile force

C. Resist fracture due to high impact loads

D. Retain deformation produced under load permanently

What is the correct answer?

4

The period during which the cam follower remains at rest, when cam moves, is known as

A. Constant period

B. Fixed period

C. Dwell period

D. Idle period

What is the correct answer?

4

A V-belt designated as B 4430 LP has

A. 4430 mm as diameter of small pulley

B. 4430 mm as nominal pitch length

C. 4430 mm as diameter of large pulley

D. 4430 mm as centre distance between pulleys

What is the correct answer?

4

The square threads are usually found on

A. Spindles of bench vices

B. Railway carriage couplings

C. Feed mechanism of machine tools

D. Screw cutting lathes

What is the correct answer?

4

Crowning on pulley helps

A. In decreasing the slip of the belt

B. In increasing the slip of the belt

C. To keep the belt in centre on a pulley while it is in motion

D. To increase pulley life

What is the correct answer?

4

Taper usually provided on cotter is

A. 1 in 5

B. 1 in 10

C. 1 in 24

D. 1 in 40

What is the correct answer?

4

Eulers formula for a mild steel column is not valid if the slenderness ratio is

A. 90

B. 60

C. 120

D. 100

What is the correct answer?

4

The difference between the tooth space and the tooth thickness as measured on the pitch circle, is called

A. Working depth

B. Clearance

C. Backlash

D. Face width

What is the correct answer?

4

For a shaft diameter of 100 mm, the number of bolts in a flange coupling should be

A. 4

B. 6

C. 8

D. 10

What is the correct answer?

4

Stress concentration factor is defined as the ratio of

A. Maximum stress to the endurance limit

B. Nominal stress to the endurance limit

C. Maximum stress to the nominal stress

D. Nominal stress to the maximum stress

What is the correct answer?

4

The resistance to fatigue of a material is measured by

A. Elastic limit

B. Ultimate tensile strength

C. Young's modulus

D. Endurance limit

What is the correct answer?

4

Which of the following key is preferred for the condition when a large amount of impact type torque is to be transmitted in both direction of rotation?

A. Woodruff key

B. Feather key

C. Gib-head key

D. Tangent key

What is the correct answer?

4

The stiffness of a closely coiled helical spring subjected to an axial load W is equal to (where G = Modulus of rigidity, and n = Number of active coils)

A. Gd⁴/ 8D3n

B. Gd3/ 8D3n

C. Gd⁴/ 4D3n

D. Gd⁴/ 8D²n

What is the correct answer?

4

The velocity factor for very accurately cut and ground metallic gears operating at velocities upto __________ are equal to 6/(6 + v).

A. 10 m/s

B. 12.5 m/s

C. 15 m/s

D. 20 m/s

What is the correct answer?

4

In designing thick cylinders, the equation used is

A. Lame's equation

B. Birnie's equation

C. Clavarinos' equation

D. All of these