Related Questions
What is the correct answer?
4
The yield point in static loading is __________ as compared to fatigue loading.
What is the correct answer?
4
Which of the following statement is correct?
A. The distance from a point on one thread to the corresponding point on the next thread is called pitch
B. The distance which a screw thread advances axially in one rotation of the nut is called lead
C. In single start threads, lead is equal to pitch
What is the correct answer?
4
According to Unwin's formula, the relation between the diameter of rivet hole (d) and the thickness of plate (t) is given by (where d and t are in mm)
What is the correct answer?
4
In designing a connecting rod, it is considered like __________ for buckling about X-axis.
C. One end fixed and the other end hinged
D. One end fixed and the other end free
What is the correct answer?
4
According to I.B.R., the factor of safety of riveted joint should not be less than
What is the correct answer?
4
A key capable of tilting in a recess milled out in a shaft is known as
What is the correct answer?
4
Ball bearing type screws are found in following application
What is the correct answer?
4
A column of length l is fixed at both ends. The equivalent length of the column is
What is the correct answer?
4
Shear stress theory is applicable for
What is the correct answer?
4
Eulers formula for a mild steel column is not valid if the slenderness ratio is
What is the correct answer?
4
An elastic bar is fixed at the upper end and loaded at the lower end by a falling weight. The shock load produced can be reduced by
A. Increasing the length of bar
B. Decreasing the cross-sectional area of the bar
C. Decreasing the modulus of elasticity of the bar
What is the correct answer?
4
A spring of stiffness 1000 N/m is stretched initially by 100 mm from the undeformed position. The work required to stretch it by another 100 mm is
What is the correct answer?
4
In the levers of first type, the mechanical advantage is __________ one.
What is the correct answer?
4
The property of a material which enables it to be drawn into wires with the application of a tensile force, is called
What is the correct answer?
4
Which of the following statement is wrong?
A. A key is used as a temporary fastening
B. A key is subjected to tensile stresses
C. A key is always inserted parallel to the axis of the shaft
D. A key prevents relative motion between the shaft and boss of the pulley
What is the correct answer?
4
When a material is subjected to fatigue loading, the ratio of the endurance limit to the ultimate tensile strength is
What is the correct answer?
4
The temperature at which the new grains are formed in the metal is known as
A. Lower critical temperature
B. Upper critical temperature
C. Recrystallisation temperature
What is the correct answer?
4
If the centre distance of the mating gears having involute teeth is increased, then the pressure angle
What is the correct answer?
4
When two helical springs of equal lengths are arranged to form a cluster spring, then
A. Shear stress in each spring will be equal
B. Load taken by each spring will be half the total load
D. Both A and B is correct
What is the correct answer?
4
Three different weights fall from a certain height under vacuum. They will take
A. Same time to reach earth
B. Times proportional to weight to reach earth
C. Times inversely proportional to weight to reach earth
What is the correct answer?
4
A tube has the following advantage over pipe
A. Lighter and easier to handle
B. Greater shock absorption
What is the correct answer?
4
The crest diameter of a screw thread is same as
What is the correct answer?
4
In a transverse fillet welded joint, the size of weld is __________ the throat of weld.
What is the correct answer?
4
The speed of the sprocket reduces as the chain pitch __________ for a given number of teeth.
What is the correct answer?
4
The following type of nut is used with alien bolt
What is the correct answer?
4
The difference between the tooth space and the tooth thickness as measured on the pitch circle, is called
What is the correct answer?
4
The lower deviation is the algebraic difference between the
A. Actual size and the corresponding basic size
B. Maximum limit and the basic size
C. Minimum limit and the basic size
What is the correct answer?
4
A double fillet welded joint with parallel fillet weld of length l and leg s is subjected to a tensile force P. Assuming uniform stress distribution, the shear stress in the weld is given by
What is the correct answer?
4
The objective of idler pulley in belt drive is to
A. Decrease the tendency of belt to slip
B. Increase the power transmission capacity
C. Increase the wrap angle and belt tension
D. All the above objectives
What is the correct answer?
4
The application of third type levers is found in
B. Hand wheel of a punching press
C. Lever of a loaded safety valve