Related Questions
What is the correct answer?
4
Dielectric
A. Is an electrical insulating material
B. Of low resistivity is preferred
C. Should have high thermal conductivity
D. Need not defy the corrosive action of chemicals
What is the correct answer?
4
Removal of non-condensable from steam or other vapour is termed as the __________ process.
What is the correct answer?
4
__________ is the most important element, which controls the physical properties of steel.
What is the correct answer?
4
As per international norms, the maximum permissible value of noise level in the industrial environment is __________ decibels as measured at a distance of 1.5 metres from the source of noise.
What is the correct answer?
4
Uniform ramming of sand in green sand moulding process leads to
A. Reduced chance of gas porosity
B. Greater dimensional stability of the casting
C. Uniform flow of molten metal into the mould cavity
D. Less sand expansion type of casting defect
What is the correct answer?
4
The refractory lining of the bottom in a basic electric arc furnace is made of
What is the correct answer?
4
Consider the equilibrium A(g) + B(g) = AB(g). When the partial pressure of A is 10-2 atm, the partial pressure of B is 10-3 atm and the partial pressure of AB is 1 atm, the equilibrium constant 'K' is
What is the correct answer?
4
Common salt is produced from sea water in India generally by the __________ method.
What is the correct answer?
4
Brazing filler metal used for joining steel plates
A. Melts below the melting points of base metals
C. Is copper phosphorous alloy
What is the correct answer?
4
In a boundary layer developed along the flow, the pressure decreases in the downstream direction. The boundary layer thickness in this case will
What is the correct answer?
4
During decarburising of a plain carbon steel, the thickness of ferrite layer growth is proportional to
What is the correct answer?
4
Steam condenser tubes are made of admiralty brass, in which percentage of zinc & copper are __________ respectively.
What is the correct answer?
4
The normal stress is the same in all directions at a point in a fluid, only when the fluid
A. Is at rest & has zero viscosity
C. Fluid layer has no motion relative to an adjacent layer of fluid
D. is incompressible & frictionless
What is the correct answer?
4
Normalising does not __________ of a metal.
A. Improve machinability & tensile strength
B. Remove internal stresses
D. Remove strains caused by cold working
What is the correct answer?
4
Stainless steel is welded with difficulty because of
A. Its high melting temperature
D. Chromium carbide formation
What is the correct answer?
4
Which of the following heat treatment processes is usually applied to castings?
What is the correct answer?
4
__________ pipe is the most suitable for carrying sanitary drainage.
B. Reinforced cement concrete
What is the correct answer?
4
Use of water as a manometric liquid suffers from the disadvantage of its
What is the correct answer?
4
Closeness of packing is maximum in case of __________ crystal lattice.
What is the correct answer?
4
Large scale fire on fuel gas line is normally extinguished by
What is the correct answer?
4
Resilience of a bolt can be increased by increasing its
What is the correct answer?
4
The approximate height of a blast furnace having a useful volume of 2000 m3 is about __________ metres
What is the correct answer?
4
__________ of hard alloy and tool steel is done to make it easily machinable.
What is the correct answer?
4
Which of the following materials has the maximum shrinkage allowance?
What is the correct answer?
4
The mechanism which changes the value of manipulated variable in response to the output signal from the control unit is called the
C. Floating control action
What is the correct answer?
4
According to thermodynamic Fahrenheit scale, the fundamental interval between ice point to steam point is
What is the correct answer?
4
Maximum permissible sulphur content in steel is __________ percent.
What is the correct answer?
4
The thickness of oxide film is y at time t. If are the temperature dependent constants, the parabolic law of oxidation is given by
What is the correct answer?
4
'GASOHOL' widely used in Brazil as a motor fuel is a mixture of alcohol and
C. Light hydrocarbon gases (e.g. butane or propane)
What is the correct answer?
4
What happens, when SO2 is passed through a solution of H2S in water?
A. Precipitation of sulphur takes place