Home
Current Affairs January 2024

What is the correct answer?

4

As the fluid flow rate increases, the float of the Rotameter

A. Rises in the tube

B. Rotates at higher speed

C. Rotates at lower speed

D. Drops down in the tube

Correct Answer :

A. Rises in the tube


Related Questions

What is the correct answer?

4

__________ of austenite decreases the hardenability in steel.

A. Fine grains

B. Coarse grains

C. Homogeneity

D. Dissolved elements (except cobalt)

What is the correct answer?

4

If the demand for an item is trebled and the order cost is reduced to one third, then the economic order quantity

A. Is trebled

B. Remains unchanged

C. Decreases by a factor of 3

D. Decreases by a factor of 1/3

What is the correct answer?

4

Sacrificial anode method is used in the protection of pipelines which are buried underground. Sacrificial anode

A. Occurs higher in the electro-chemical series of metals

B. Is exemplified by magnesium plate

C. Is much cheaper than the cathodic base material to be guarded against corrosion

D. All (A), (B) & (C)

What is the correct answer?

4

For the Stoke's law to be valid in the case of a falling sphere in a fluid, the

A. Reynolds number (based on sphere diameter) should be < 1

B. Flow around the sphere should be in turbulent region

C. Sphere must be metallic

D. Fluid density should be constant

What is the correct answer?

4

With increase in __________ Knocking tendency in a spark ignition petrol engine decreases.

A. Supercharging

B. Wall temperature

C. Compression ratio

D. Engine speed

What is the correct answer?

4

Which of the following are considered applications of ultrasonic testing?

A. Determination of elastic constant

B. Detection of defects in metal

C. Measurement of material thickness

D. None of the above

What is the correct answer?

4

Coating thickness in case of galvanising of steel sheet generally corresponds to the deposition of __________ gms of zinc per of steel strip.

A. 5-10

B. 1000-1500

C. 120-500

D. 1500-3000

What is the correct answer?

4

Work study deals with the __________ study.

A. Time

B. Motion

C. Both (A) & (B)

D. Neither (A) nor (B)

What is the correct answer?

4

Tempering of a material does not improve its

A. Machinability

B. Toughness

C. Internal stress level

D. Softness

What is the correct answer?

4

A jet engine turbine blade is normally manufactured by

A. Forging

B. Shell moulding

C. Investment casting

D. Pressure die casting

What is the correct answer?

4

Globular form of cementite is formed during the __________ process.

A. Spheroidising

B. Hardening

C. Annealing

D. Normalising

What is the correct answer?

4

__________ has the highest melting point out of the following.

A. Tungsten

B. Zirconium

C. Molybdenum

D. Tantalum

What is the correct answer?

4

__________ is a special constituent of chlorophyll without which photosynthesis is not possible.

A. Calcium

B. Nitrogen

C. Phosphorous

D. Hydrogen

What is the correct answer?

4

Pick out the wrong statement.

A. A soft magnetic material should have high permeability and small area of hysteresis loop

B. Poisson's ratio of high melting point metals is more than unity

C. Solders generally melt at less than 185°C

D. Steel produced by B.O.F process is ideally suited for manufacturing flat product

What is the correct answer?

4

__________ flux is used for the extraction of metal from its self fluxing ores.

A. No

B. Acid

C. Basic

D. Neutral

What is the correct answer?

4

The product out from a cupola is called

A. Wrought iron

B. Pig iron

C. Cast iron

D. None of these

What is the correct answer?

4

Large diameter reinforced cement concrete (RCC) pipes are generally joined by __________ joint.

A. Flanged iron

B. Collar

C. Flexible

D. Expansion

What is the correct answer?

4

Silicon percentage in acid resistant cast iron is about

A. 4

B. 8

C. 14

D. 20

What is the correct answer?

4

Which of the following has the highest modulus of elasticity (about 7 × 106 kg/cm2)?

A. High speed steel

B. Stainless steel

C. Tungsten carbide

D. Superalloys

What is the correct answer?

4

Melting point & boiling points of liquid oxygen are respectively - 218.8°C & - 183°C, while the same for liquid nitrogen is - 210°C & - 195.8°C respectively. The difference in melting points of liquid oxygen & liquid nitrogen is not equal to 8.8

A. °C

B. °F

C. °K

D. °R

What is the correct answer?

4

The escape velocity of a body on earth which is independent of its mass is about __________ km/second.

A. 3

B. 7

C. 11

D. 15

What is the correct answer?

4

Pick out the wrong statement.

A. Molecules with symmetrical arrangements (e.g. CH4 or CCl4) are non-polar

B. Generally, non-polar compounds are chemically inactive, conduct electricity poorly and do not ionise

C. Most of the hydrocarbons are non-polar

D. None of these

What is the correct answer?

4

Encyclopaedia of Chemical Technology has been

A. Authored by Kirk Othmer

B. Edited by Perry and Chilton

C. Edited by Kirk Othmer

D. Authored by Perry and Chilton

What is the correct answer?

4

'Ice point' is designated on Fahrenheit temperature scale by

A.

B. 32°

C. 62°

D. 212°

What is the correct answer?

4

In __________ process, there is an increase in entropy with no degradation of energy.

A. Isothermal expansion

B. Isochoric heat addition

C. Polytropic expansion

D. Isobaric heat addition

What is the correct answer?

4

Out of the following substances, one ton of __________ will store the maximum heat for a rise of 30°C in temperature.

A. Steel

B. Lignite

C. Water

D. Lime stone

What is the correct answer?

4

__________ is not used as the control rod material in a nuclear reactor.

A. Cobalt

B. Hafnium

C. Cadmium

D. Boron

What is the correct answer?

4

Which of the following is not a principal alloying element for the structural steel?

A. Molybdenum

B. Nickel

C. Manganese

D. Chromium

What is the correct answer?

4

Hot dipping process is used for coating a low melting point metal (e.g. Pb, Sn, Zn) on iron, steel & copper having relatively higher melting points. Which of the following is not a hot dipping process?

A. Galvanising

B. Tinning

C. Sherardizing

D. None of these

What is the correct answer?

4

The critical pressure at which the latent heat of vaporisation of steam becomes zero is __________ Kg/cm2.

A. 273.15

B. 225.65

C. 100.03

D. 373.15