Related Questions
What is the correct answer?
4
When using versions of Auto-CAD prior to Release 2006 it may be necessary to ________ a block in order to edit it.
What is the correct answer?
4
Dimension text is generally placed above the ________ line.
What is the correct answer?
4
There should be a visible gap between the wall and the ________ line.
What is the correct answer?
4
Auto-CAD refers to isometric ellipses as ________.
What is the correct answer?
4
Generally, the units used on an architectural drawing are set to ________.
What is the correct answer?
4
Understanding the Cartesian coordinate system will help the beginning drafter ________.
A. Control the accuracy of the drawing
B. Produce a visible grid system
C. Select a different text style
D. Choose various line types
What is the correct answer?
4
The site plan illustrates ________.
B. Where the house sits on the property
D. Where the garage and driveway are located
What is the correct answer?
4
Placement of dimensions on a drawing is controlled by ________.
C. Corporate drafting standards
What is the correct answer?
4
The thread note for a typical bolt will include the ________.
A. Major diameter of the thread
What is the correct answer?
4
One way to evenly space dimensions on a drawing is to use the ________.
What is the correct answer?
4
The View toolbar will position the view of the 3-D solid toward the ________.
What is the correct answer?
4
This is the theoretically exact size from which limits of size are determined:
What is the correct answer?
4
On a floor plan the dashed line that appears approximately 24 outside the exterior wall represents the __________.
What is the correct answer?
4
The 3-D commands on the Modeling toolbar include ________.
What is the correct answer?
4
A half-moon protractor is divided into how many degrees?
What is the correct answer?
4
The edges of a cube in isometric projection make angles of this many degrees with each other:
What is the correct answer?
4
When creating your own blocks it is important to avoid drawing any portion of the block in the ________ layer.
What is the correct answer?
4
4.The principle reason for using an auxiliary view is ________.
A. To eliminate hidden lines
B. To create a true projection plane from an inclined plane in one of the primary views
C. To show cylinders as ellipses
D. To locate center marks
What is the correct answer?
4
This type of circuit is a semiconductor wafer or chip:
What is the correct answer?
4
Schematic and single-line diagrams should be arranged so that signal or transmission path from input to output proceeds in this fashion:
A. Right to left and top to bottom
B. Right to left and bottom to top
C. Left to right and top to bottom
D. Left to right and bottom to top
What is the correct answer?
4
These gears transmit power between shafts whose axes intersect at any angle:
What is the correct answer?
4
When positioning this feature of perspective projection, the centerline of the cone of visual rays should be directed toward the approximate center of the object:
What is the correct answer?
4
The ________ dimension tool will place the length of an angled line.
What is the correct answer?
4
PDM is the acronym for:
A. Project drawing management
B. Product drawing manipulation
C. Product data management
D. Project data manipulation
What is the correct answer?
4
This is used in drawings to represent the edge of a solid object:
What is the correct answer?
4
This line pattern is composed of three dashes, one long dash on each end with a short dash in the middle:
What is the correct answer?
4
This type of axonometric drawing has equal foreshortening along two axis directions and a different amount on the third axis:
What is the correct answer?
4
Some traditional board drafters preferred the drafting machine over the parallel straight edge because it could be used without the need for________.
What is the correct answer?
4
Referring to the fractional inches to decimal inches to millimetre conversion chart on page 55 what is the equivalent mm measurement of 3/16 inch.
What is the correct answer?
4
This is a rounded exterior blend between surfaces: