Related Questions
What is the correct answer?
4
Fibre glass is a composite material of
A. Glass fibre in a polymer matrix
B. Glass fibre in a metallic matrix
C. Polymer fibre in a glassy matrix
What is the correct answer?
4
Primary designation of steel is based on its
A. Hardness & tensile strength
D. Alloying elements content
What is the correct answer?
4
The laminar boundary layer thickness in zero pressure gradient flow over a flat plate along the x-direction varies as x0.5 while the thickness of turbulent boundary layer varies as (where, x = distance from the leading edge)
What is the correct answer?
4
The cathode in an electrochemical cell always carries
D. Positive or negative charge depending upon the nature of the cell
What is the correct answer?
4
The two elements required to form substitutional solid solution should not have
A. Same crystalline structure
C. Widely differing electronegativity
What is the correct answer?
4
In the formation of cermets, the ratio of ceramic material to metallic material is usually 80:20. Which of the following is a cermet?
What is the correct answer?
4
Broaching tools are usually made of
What is the correct answer?
4
Which of the following is not a charge material for cupola?
What is the correct answer?
4
Carnot cycle is also termed as the constant __________ cycle in thermodynamics.
What is the correct answer?
4
The refrigerant freon-12 is chemically
What is the correct answer?
4
As per international norms, the maximum permissible value of noise level in the industrial environment is __________ decibels as measured at a distance of 1.5 metres from the source of noise.
What is the correct answer?
4
Material of construction of the electrode used in the electric resistance welding is
What is the correct answer?
4
Temperature profile along the length of a gasgas counter flow heat exchanger is correctly represented by
What is the correct answer?
4
The best lubricants for a machine working at high temperature & load is
What is the correct answer?
4
A 2 kg object weighs 1.8 kgf on a spring balance. The value of 'g' at that location in m/sec2 is
What is the correct answer?
4
Which of the following fastening devices has its both ends threaded?
What is the correct answer?
4
Matte smelting is used in the extraction of
What is the correct answer?
4
Often earing defects are found during deep drawing operation, because the
A. Surface finish of the sheet is poor
B. Sheet material has been given substantial spring back
C. Starting sheet has planer anisotropy due to its texture
D. Starting sheet has normal anisotropy due to its texture
What is the correct answer?
4
The emf of a Deniell cell Zn | Zn2+ || Cu2+ | Cu can be increased by
A. Decreasing the surface area of the electrodes
B. Increasing the concentration of zinc sulphate solution
C. Increasing the surface area of the electrodes
D. Increasing the concentration of copper sulphate solution
What is the correct answer?
4
Unit of viscosity in CGS system is
What is the correct answer?
4
Increase in the entropy of a system represents the
B. Decrease in system pressure
C. Increase in the availability of energy
D. Increase in the temperature
What is the correct answer?
4
Fire in fuel gas pipelines is extinguished most effectively by
B. Blanketting the area with nitrogen atmosphere
What is the correct answer?
4
In a good rimming steel
A. Carbon and silicon should be low
B. Silicon should be low but carbon should be high
C. Both silicon & carbon should be high
D. Silicon should be high but carbon should be low
What is the correct answer?
4
Rankine cycle comprises of two isothermal and two __________ processes.
What is the correct answer?
4
A particle is settling in a liquid under Stokesian conditions. The free falling velocity of the particle is proportional to
What is the correct answer?
4
Thermal conductivity of a material does not depend upon its
What is the correct answer?
4
Induced draft fans provided in large thermal power plant boilers have __________ blades.
What is the correct answer?
4
In TIG welding, thoriated tungsten electrodes are used, because it
A. Has higher current carrying capacity
B. Has better electron emissivity
C. Is stronger than ordinary tungsten
What is the correct answer?
4
A jet engine turbine blade is normally manufactured by
What is the correct answer?
4
Mild steel has __________ crystal lattice structure.
A. Face centred cubic (fcc)
B. Body centred cubic (bcc)