Related Questions
What is the correct answer?
4
Out of the following, the joint produced by __________ has the lowest strength.
What is the correct answer?
4
Friction factor for fluid flow in pipe does not depend upon the
C. Fluid density & viscosity
D. Mass flow rate of fluid
What is the correct answer?
4
Which of the following contributes maximum as main source of sulphur in the blast furnace charge?
What is the correct answer?
4
Heat release during phase change is observed in case of a/an
What is the correct answer?
4
Hardening of steel is not possible, unless it is heated __________ critical point.
C. Between the first & second
D. Between the second & third
What is the correct answer?
4
The following type of bonding is strongly directional in solids.
What is the correct answer?
4
__________ can replace tungsten in high speed steel.
What is the correct answer?
4
Faraday's law of electrolysis is related to the
B. Atomic number of the cation
C. Equivalent mass of the electrolyte
What is the correct answer?
4
Which of the following approaches the ideal gas behaviour most closely?
What is the correct answer?
4
Work study deals with the __________ study.
What is the correct answer?
4
__________ glass is used in the mercury in glass thermometer meant for measuring a temperature of 500°C.
What is the correct answer?
4
Metal cutting by oxy-acetylene flame is accomplished by the __________ of the metal.
What is the correct answer?
4
Silicon crystal can be converted to p-type semiconductor by doping with
What is the correct answer?
4
Force between the molecules of the same substance is called __________ force.
What is the correct answer?
4
Flue gases pass through the following boiler accessories in a high pressure natural circulation boiler.
A. Induced draft fan
B. Economiser
C. Air preheater
D. Steam superheater Which of the following gives the correct sequence of flow of the flue gases through the above mentioned boiler accessories?
What is the correct answer?
4
__________ flux is used for the extraction of metal from its self fluxing ores.
What is the correct answer?
4
The passage between the nozzle and the __________ is called 'sprue' in case of injection moulding.
What is the correct answer?
4
Leakage in a cooking gas cylinder is detected by
B. Pouring soap solution on the surface and locating the gas bubbles
D. Pungent smell of mercaptans present in the gas
What is the correct answer?
4
A material is capable of resisting softening at high temperature, because of its property termed as
What is the correct answer?
4
The maximum thickness of the metal which can be welded using ultrasonic welding is __________ mm.
What is the correct answer?
4
Auto collimator is used to check
What is the correct answer?
4
Factor of safety in machine design is defined as the ratio of ultimate stress to __________ stress.
What is the correct answer?
4
At 100% relative humidity, the dew point temperature of moist air is
A. Less than the wet bulb temperature
B. More than the wet bulb temperature
C. Equal to the wet bulb temperature
D. Equal to the ambient temperature
What is the correct answer?
4
Other parameters remaining same, the recrystallisation temperature of an alloy is lowered, when
A. Strain rate is increased
B. Grain size is increased
C. Prior cold deformation is increased
D. Not affected by any of the above parameters
What is the correct answer?
4
Notched bar test is used for testing the __________ of a material.
What is the correct answer?
4
Evaporative cooling process employs a combination of cooling and humidification in which the
A. Sensible heat is added
B. Sensible heat is removed and the latent heat is added
C. Latent heat is removed
D. Sensible heat is added and latent heat is removed
What is the correct answer?
4
Electrochemical corrosion can occur, only if __________ is present in contact with metal.
What is the correct answer?
4
Even though heat transfer co-efficient in boiling liquids is large, use of fins is advantageous, when the entire surface is exposed to __________ boiling.
What is the correct answer?
4
Normalising of an object does not
A. Refine coarse grain structure obtained during hot working
C. Improve yield strength
D. Improve mechanical properties
What is the correct answer?
4
Tesla metre per ampere (T. m/A) is the unit for the measurement of
A. Magnetic susceptibility
C. Permeability of free space