Related Questions
What is the correct answer?
4
Which of the following commonly used condenser tube materials has the lowest thermal conductivity?
What is the correct answer?
4
Which of the following is an unconventional source of energy?
What is the correct answer?
4
Dislocation cross-slip is difficult in those materials, which have
A. Large number of slip systems
B. High work hardening rate
D. Low stacking fault energy
What is the correct answer?
4
Maximum heat dissipation occurs from a steel wire (k = 0.5 W/m. k) of 15 mm diameter exposed to air (h = 20W/m2 .k), when the insulation thickness is __________ mm.
What is the correct answer?
4
The most important consideration in value engineering is the
What is the correct answer?
4
Oxygen cylinders used for autogenous (cutting/welding) purposes are
A. Seamless & made of steel
B. Heat treated before use
D. Welded steel cylinders
What is the correct answer?
4
Temperature of hot gases flowing in a pipe is measured by a thermocouple inserted in the thermal well. The thermal well made of __________ will facilitate the most accurate measurement of the temperature.
What is the correct answer?
4
Which of the following are made out of the carbon steel having carbon content of 0.9 to 1%?
A. Small punches, broaches reamers and springs
B. Cutlery, screws, rivets and files
C. Mandrels, twist drills, small lathe tools and razors
D. Forgings like can shaft, structural steel plate, threading dies and drawing dies
What is the correct answer?
4
The majority charge carriers in p-type silicon are
What is the correct answer?
4
__________ property of steel increases by addition of large amount of silicon in it.
What is the correct answer?
4
Shrinkage allowance on pattern is provided to compensate for shrinkage when the
A. Metal changes from liquid state to solid state at freezing temperature
B. Solid phase temperature drops from freezing temperature to the room temperature
C. Liquid metal temperature drops from pouring temperature to room temperature
D. Liquid metal temperature drops from pouring temperature to freezing temperature
What is the correct answer?
4
A spring material should have low
What is the correct answer?
4
Lead is poured into the joints between two __________ pipes.
What is the correct answer?
4
Which of the following varies as the square root of oil pressure during atomisation of fuel oil through a pressure jet burner?
What is the correct answer?
4
The two elements required to form substitutional solid solution should not have
A. Same crystalline structure
C. Widely differing electronegativity
What is the correct answer?
4
Friction factor for fluid flow in pipe does not depend upon the
C. Fluid density & viscosity
D. Mass flow rate of fluid
What is the correct answer?
4
__________ furnace is generally used in the non-ferrous foundries.
What is the correct answer?
4
Resilience of a bolt can be increased by increasing its
What is the correct answer?
4
A metal having a Poisson's ratio = 0.3 is elastically deformed under uniaxial tension. If the longitudinal strain = 0.8, then the magnitude of thickness strain is
What is the correct answer?
4
Which of the following mainly decides the current to be employed is arc welding?
C. Voltage across the arc
What is the correct answer?
4
Air/fuel ratio by weight for combustion of methane with theoretical quantity of air will be about
What is the correct answer?
4
One face of a furnace wall is at 1030°C and the other face is exposed to room temperature (30°C). If the thermal conductivity of furnace wall is 3 W. m- 1. k-1 and the wall thickness is 0.3 m, the maximum heat loss (in W/m) is
What is the correct answer?
4
If Reynolds number is greater than 1, then the
A. Viscous force is larger than the inertia force
B. Inertia force is larger than the viscous force
C. Inertia force is larger than the surface tension force
D. Inertia force is larger than the gravitational force
What is the correct answer?
4
Density in the solid state is slightly less than that in its liquid state, in case of
What is the correct answer?
4
Melting point & boiling points of liquid oxygen are respectively - 218.8°C & - 183°C, while the same for liquid nitrogen is - 210°C & - 195.8°C respectively. The difference in melting points of liquid oxygen & liquid nitrogen is not equal to 8.8
What is the correct answer?
4
The materials which fracture even at small strains are termed as brittle, while those materials which exhibit an appreciable deformation before failure are termed as
What is the correct answer?
4
Elimination of brittleness resulting from welding of saw blades is done by __________ of the welded portion.
What is the correct answer?
4
Two solutions A1 & A2 have pH value of 2 & 6 respectively. It implies that the solution
A. A1 is more alkaline than solution A2
C. A2 is very slightly acidic
What is the correct answer?
4
Hot extrusion of aluminium is done in the temperature range of __________ °C.
What is the correct answer?
4
Hydro-cyclone is a