Related Questions
What is the correct answer?
4
Half life of a radioactive isotope corresponds to the time required for half of the __________ to decay.
What is the correct answer?
4
The thickness of oxide film is y at time t. If are the temperature dependent constants, the parabolic law of oxidation is given by
What is the correct answer?
4
Nusselt number is related to the Reynolds number (Re) in turbulent & laminar flow respectively as
What is the correct answer?
4
Function of gear box is to
What is the correct answer?
4
Thermit welding is categorised as the __________ welding.
What is the correct answer?
4
Increasing sulphur content in pig iron tends to make it
What is the correct answer?
4
For separating small pieces of metal from engine oil of a car, the best separating technique is the
D. Fractional distillation
What is the correct answer?
4
Energy of the sun arises mainly from __________ reactions.
What is the correct answer?
4
Which of the following is prone to cup and cone fracture?
C. Round specimen of ductile metal
D. Flat tensile specimen of ductile metal
What is the correct answer?
4
Venturimeter is used to measure the flow rate of fluids in pipes, when the pipe is in __________ position.
What is the correct answer?
4
Cold cracking in the heat affected zone of a high strength steel weld can take place because of the
C. Relatively high sulphur content in the base metal
D. Sufficient hydrogen present in the welding arc
What is the correct answer?
4
Spherical shape of mercury droplets is due to its
What is the correct answer?
4
__________ circuit is most commonly used to measure strain with the help of a strain gauge.
B. Voltage balancing potentiometric
C. Simple current sensitive
What is the correct answer?
4
Use of economiser in a boiler plant reduces the fuel consumption for steam generation by about __________ percent.
What is the correct answer?
4
A compact estimate about the amount of materials handling between various work stations is obtained from the
What is the correct answer?
4
Carbide tipped cutting tools are manufactured by powder metallurgy techniques and have a composition of
A. 90% tungsten carbide and 10% cobalt
B. 70% aluminium oxide & 30% silica
C. 30% nickel, 15% chromium & 55% tungsten
D. 65% tungsten & 35% zirconium
What is the correct answer?
4
A solid aluminium ball, when quenched in a water bath maintained at 40°C, cools down from 550°C to 450°C in 20 seconds. The expected temperature of the ball after next 20 seconds may be about __________ °C.
What is the correct answer?
4
Brittleness induced due to the presence of sulphur in steel can be reduced by adding
What is the correct answer?
4
__________ is not a case hardening process.
What is the correct answer?
4
Alumina, silica, lime and iron oxide are the basic raw material for the manufacture of Portland cement. The component of Portland cement which first hardens is
What is the correct answer?
4
Upto the critical radius of insulation, added insulation, will
A. Increase the heat loss
B. Decrease heat loss and will have no effect beyond that
D. Reduce convection heat loss compared to conduction heat less
What is the correct answer?
4
Normalising does not __________ of a metal.
A. Improve machinability & tensile strength
B. Remove internal stresses
D. Remove strains caused by cold working
What is the correct answer?
4
Quartz is a __________ material.
What is the correct answer?
4
The life of a ball bearing is inversely proportional to
What is the correct answer?
4
In the acid Bessemer process, the hot metal should have the following composition.
A. S < 0.05% and P < 0.05%
B. S < 0.05% and P < 1.5%
C. S < 0.05% and P > 1.5%
D. S > 1.5% and P < 0.05%
What is the correct answer?
4
High relative humidity decreases the evaporative process and as the temperature is increased, the relative humidity decreases. The comfort range for human body is the ambient temperature of 22 to 27°C with relative humidity ranging from __________ percent.
What is the correct answer?
4
Pearlite comprises of
A. 87% cementite & 13% Fe
B. 87% ferrite & 13% cementite
C. 93.33% ferrite & 6.67% C
What is the correct answer?
4
In TIG welding, thoriated tungsten electrodes are used, because it
A. Has higher current carrying capacity
B. Has better electron emissivity
C. Is stronger than ordinary tungsten
What is the correct answer?
4
Which of the following low melting alloy containing bismuth and lead is used for electric fuse?
What is the correct answer?
4
One of the methods of purification of leach liquor is ion exchange, which involves
A. Exchange between two liquid phases
B. Exchange between a gaseous phase and a liquid phase
C. Exchange between a liquid phase and an organic resin phase
D. Exchange between a solid phase and a gas phase