Related Questions
What is the correct answer?
4
The bending moment M and a torque T is applied on a solid circular shaft. If the maximum bending stress equals to maximum shear stress developed, then M is equal to
What is the correct answer?
4
The maximum bending stress in a curved beam having symmetrical section always occur at the
What is the correct answer?
4
A thin spherical shell of internal diameter d is subjected to an internal pressure p. If V is the storage capacity of shell, then its diameter will be
What is the correct answer?
4
In a journal bearing, the load on the bearing is __________ to the axis of the journal.
What is the correct answer?
4
The resultant axial load on a bolt depends on
C. Relative elastic yielding (springness) of the bolt and the connected member
What is the correct answer?
4
If a spring is cut down into two springs, the stiffness of cut springs will be
What is the correct answer?
4
In designing a sleeve coupling, length of the sleeve is taken as (where d = Diameter of the shaft)
What is the correct answer?
4
The largest diameter of an external or internal screw thread is known as
What is the correct answer?
4
When an open coiled helical compression spring is subjected to an axial compressive load, the maximum shear stress induced in the wire is (where D = Mean diameter of the spring coil, d = Diameter of the spring wire, K = Wahl's stress factor, and W = Axial compressive load on the spring)
What is the correct answer?
4
Which one of the following is a positive drive?
C. Crossed flat belt drive
What is the correct answer?
4
In unilateral system of tolerance, the tolerance is allowed on
A. Both sides of the actual size
B. One side of the actual size
C. One side of the nominal size
D. Both sides of the nominal size
What is the correct answer?
4
A leaf spring in automobiles is used
D. To store strain energy
What is the correct answer?
4
A locking device in which the bottom cylindrical portion is recessed to receive the tip of the locking set screw, is called
What is the correct answer?
4
Which is correct statement?
A. A member made of steel will generally be more rigid than a member of equal load carrying ability made of cast iron
B. A member made of cast iron will generally be more rigid than a member of equal load carrying ability made of steel
C. Both will be equally rigid
D. Which one is rigid will depend on several other factors
What is the correct answer?
4
The application of third type levers is found in
B. Hand wheel of a punching press
C. Lever of a loaded safety valve
What is the correct answer?
4
The ratio of driving tensions for flat belts, neglecting centrifugal tension, is (where T₁, and T₂ = Tensions on the tight and slack sides of belt respectively, μ = Coefficient of friction, between the belt and pulley, and θ = Angle of contact)
What is the correct answer?
4
In hydrostatic bearings
A. The Oil film pressure is generated only by the rotation of the journal
B. The oil film is maintained by supplying oil under pressure
C. Do not require external supply of lubricant
D. Grease is used for lubrication
What is the correct answer?
4
A shaft is subjected to fluctuating loads for which the normal torque (T) and bending moment (M) are 1000 N-m and 500 N-m respectively. If the combined shock and fatigue factor for bending is 1.5 and combined shock and fatigue factor for torsion is 2, then the equivalent twisting moment for the shaft is
What is the correct answer?
4
Tensile strength of a mild steel specimen can be roughly predicted from following hardness test
What is the correct answer?
4
Which of the following pipe joints would be suitable for pipes carrying steam?
What is the correct answer?
4
A steel containing upto 0.15% carbon is known as
What is the correct answer?
4
The notch angle of the Izod impact test specimen is
What is the correct answer?
4
For a square key made of mild steel, the shear and crushing strength are related as
A. Shear strength is equal to crushing strength
B. Shear strength is greater than crushing strength
C. Shear strength is less than crushing strength
What is the correct answer?
4
The maximum normal stress theory is used for
What is the correct answer?
4
A fast and loose pulley drive is used when
A. Shafts are arranged parallel and rotate in the opposite directions
B. Shafts are arranged parallel and rotate in the same directions
C. Shafts are arranged at right angles and rotate in one definite direction
D. Driven shaft is to be started or stopped whenever desired without interfering with the driving shaft
What is the correct answer?
4
Aircraft body is usually fabricated by
What is the correct answer?
4
A sliding bearing in which although lubricant is present, the working surfaces __________ contact each other at least part of the time, is called boundary lubricated bearing.
What is the correct answer?
4
For a bevel gear having the pitch angle θ, the ratio of formative number of teeth (TE) to actual number of teeth (T) is
What is the correct answer?
4
The product of the diametral pitch and circular pitch is equal to
What is the correct answer?
4
According to I.B.R., when the thickness of boiler shell (t) is greater than 8 mm, then the diameter of rivet hole (d) is obtained by
A. Equating tearing resistance of the plate to the shearing resistance of the rivets
B. Equating tearing resistance of the plate to the crushing resistance of the rivets
C. Equating shearing resistance to the crushing resistance of the rivets