Related Questions
What is the correct answer?
4
Increasing sulphur content in pig iron tends to make it
What is the correct answer?
4
In a boundary layer developed along the flow, the pressure decreases in the downstream direction. The boundary layer thickness in this case will
What is the correct answer?
4
A furnace is made of a refractory brick wall of thickness 0.5 metre and thermal conductivity 0.7 W/m.°K For the same temperature drop and heat loss, this refractory wall can be replaced by a layer of diatomaceous earth of thermal conductivity 0.14 W/m.K and thickness __________ metre.
What is the correct answer?
4
__________ is a non volatile film forming constituent of a paint.
What is the correct answer?
4
__________ joint is usually used for joining cast iron pipes mostly used for temporary pipelines, where it may be necessary to dismantle & reassemble the pipeline very frequently.
What is the correct answer?
4
All of the following alloying elements of steel increases hardness but sacrifice ductility, except
What is the correct answer?
4
Which of the following metals is the most prone to work hardening?
What is the correct answer?
4
Production of a hollow product by inflation of a tube or parison is called the __________ process.
What is the correct answer?
4
__________ test can be termed as the semidestructive test.
What is the correct answer?
4
In case of a, centrifugal pump, the ratio h1/h2 is termed as the __________ efficiency (where, h1 = actual measured head & h2 = head imparted to the fluid by impeller).
What is the correct answer?
4
Depreciation of machines fails under the indirect expenses head. As per income tax regulations, it is calculated by the __________ method.
C. Multiple straight line
D. Sum of the years digit
What is the correct answer?
4
Which of the following is not an ore of copper?
What is the correct answer?
4
In the formation of cermets, the ratio of ceramic material to metallic material is usually 80:20. Which of the following is a cermet?
What is the correct answer?
4
For a thermodynamic system undergoing a process, which of the following pairs best expresses the relationship similar to that expressed by the pressure volume plot?
B. Temperature - pressure
What is the correct answer?
4
Solidification time of a molten metal in a casting is proportional to (where, V = volume of metal & A = its surface area; in the casting)
What is the correct answer?
4
A form of stress corrosion failure termed as 'season cracking' is generally observed in
A. Thermosetting polymers
What is the correct answer?
4
Melting point & boiling points of liquid oxygen are respectively - 218.8°C & - 183°C, while the same for liquid nitrogen is - 210°C & - 195.8°C respectively. The difference in melting points of liquid oxygen & liquid nitrogen is not equal to 8.8
What is the correct answer?
4
Natural water contains approximately __________ percent of heavy water.
What is the correct answer?
4
Chromium molybdenum steel cannot be welded using __________ welding.
What is the correct answer?
4
Volume of blast furnace slag is about __________ times the volume of hot metal (pig iron) of the same weight
What is the correct answer?
4
In condensers used in thermal power plants, steam is normally used in shell side and cooling water on the tube side, because of the reason that
A. Compared to the mass flow rate of cooling water, the rate of condensation of steam is invariably smaller
B. Maintaining vacuum on tube side is more difficult than that on the shell side
C. Water velocity can be increased conveniently to increase the overall heat transfer co-efficient because of its lower specific volume compared to steam
D. Condenser can act as a storage unit for condensed steam
What is the correct answer?
4
Shaft/rotor speed is most accurately measured by a
What is the correct answer?
4
Austempering process results in the formation of __________ structure.
What is the correct answer?
4
Titanium is added to molten aluminium alloys before casting for the purpose of
B. Increasing corrosion resistance
What is the correct answer?
4
Brinell Hardness Number (BHN) for talc is approximately in the range of
What is the correct answer?
4
Lead is added to 60:40 brass primarily to improve
What is the correct answer?
4
Which of the following is the most suitable material of construction for the condenser tubes, where the cooling medium is brine (salty water)?
What is the correct answer?
4
Common salt is produced from sea water in India generally by the __________ method.
What is the correct answer?
4
In an amorphous material, atoms defy any definite atomic structure and exist in random pattern just like in liquid. Which of the following is an amorphous material?
What is the correct answer?
4
The normal stress is the same in all directions at a point in a fluid, only when the fluid
A. Is at rest & has zero viscosity
C. Fluid layer has no motion relative to an adjacent layer of fluid
D. is incompressible & frictionless