Related Questions
What is the correct answer?
4
Drills are usually made of
What is the correct answer?
4
The escape velocity of a body on earth which is independent of its mass is about __________ km/second.
What is the correct answer?
4
Which of the following is an undesirable property of slag produced during the Pyrometallurgical method of metal extraction from its ore?
A. High fusibility & fluidity
B. High thermal conductivity
D. High chemical activity
What is the correct answer?
4
With increase in temperature, the surface tension of water
What is the correct answer?
4
Mho's scale of hardness, which consists of 10 standard minerals is used for the measurement of __________ hardness.
What is the correct answer?
4
Which of the following is an example of cathodic protection of metals against corrosion?
What is the correct answer?
4
Powder metallurgy process does not make metal powder by
D. Electrolytic deposition
What is the correct answer?
4
Consumable electrodes are used in the __________ welding.
What is the correct answer?
4
Pick out the correct combination about the role of various additives used in polymers.
A. Plasticiser: increases the polymer strength
B. Heat stabiliser: increases the maximum service temperature
C. Fillers: Does not affect the property of polymer but increases its weight
D. Lubricants: increases the flexibility of polymers
What is the correct answer?
4
Powder metallurgy technique is used in the production of __________ tools.
What is the correct answer?
4
Which of the following is an acidic constituent of B.F. slag?
A.
What is the correct answer?
4
Uniform ramming of sand in green sand moulding process leads to
A. Reduced chance of gas porosity
B. Greater dimensional stability of the casting
C. Uniform flow of molten metal into the mould cavity
D. Less sand expansion type of casting defect
What is the correct answer?
4
An oxidation process is accompanied with decrease in the
What is the correct answer?
4
Powder metallurgy is used to produce
A. High precision components with complex cavities and sharp features
B. Components of large size
C. Porosity free components
D. Components of such alloys whose constituents do not form alloys readily
What is the correct answer?
4
Which of the following is not an ore of copper?
What is the correct answer?
4
Out of the following, the __________ pipe has the least corrosion resistance.
What is the correct answer?
4
Cold chisel & hammers are made of
What is the correct answer?
4
Hot dipping process is used for coating a low melting point metal (e.g. Pb, Sn, Zn) on iron, steel & copper having relatively higher melting points. Which of the following is not a hot dipping process?
What is the correct answer?
4
Consider the equilibrium A(g) + B(g) = AB(g). When the partial pressure of A is 10-2 atm, the partial pressure of B is 10-3 atm and the partial pressure of AB is 1 atm, the equilibrium constant 'K' is
What is the correct answer?
4
For an ideal gas, Cp - Cv is
What is the correct answer?
4
__________ iron is produced by the annealing of white cast iron.
What is the correct answer?
4
Transition from laminar flow to turbulent flow in fluid flow through a pipe does not depend upon the
What is the correct answer?
4
The ratio of the shear stress to the principal stress on a principal plane is
What is the correct answer?
4
The joint for soldering is supported by binding wire made of
What is the correct answer?
4
Which of the following materials has the least scrap value?
What is the correct answer?
4
For a first order chemical reaction, the concentration of the reactant decreases __________ with time.
What is the correct answer?
4
Good design of the casing of a centrifugal pump aims at minimising the
What is the correct answer?
4
Oxyacetylene reducing flame is used while carrying out welding on
What is the correct answer?
4
For the Stoke's law to be valid in the case of a falling sphere in a fluid, the
A. Reynolds number (based on sphere diameter) should be < 1
B. Flow around the sphere should be in turbulent region
C. Sphere must be metallic
D. Fluid density should be constant
What is the correct answer?
4
A thin, flat & square plate measuring 2 m × 2 m is freely hanging in ambient air at 25°C. It is exposed to the solar radiation falling on one side of the plate at the rate of 500 W/m2. The plate temperature will remain constant at 30°C, if the convective heat transfer co-efficient is __________ W/m2 °C.