Related Questions
What is the correct answer?
4
What is attenuation?
C. loss of signal strength
D. unwanted signals on the network
What is the correct answer?
4
Which of the following is required to communicate between two computers?
A. Communications software
C. Communication hardware
D. All of the above including access to transmission medium
What is the correct answer?
4
What is 10baseT?
A. specification for twisted-pair cable
B. specification for cable terminators
C. 10 megawatt transceiver
D. 10 Mhz analog transfers
What is the correct answer?
4
Which of the following protocols were designed for terminal emulation to connect dissimilar systems?
D. Control Message Protocol
What is the correct answer?
4
FDDI operates on 100 Mbps.
What is the correct answer?
4
802.5 project standard defines Token Ring.
What is the correct answer?
4
Which class does the IP address 202.119.22.31 belong to?
What is the correct answer?
4
Strings enclosed in _______ quotation marks indicate single tokens.
What is the correct answer?
4
Which layer of the OSI model does a switch operate in?
What is the correct answer?
4
BGP is …………………………………….routing protocol used to ………………………….routing table.
A. intrautonomous system, update
B. Interautonomous system, update
C. Interautonomous system, create
D. intrautonomous system, create
What is the correct answer?
4
In an autonomous system with n areas, how many areas are connected to the backbone?
What is the correct answer?
4
Which of the following can provide a backbone network of 600 meters in length without using repeaters?
What is the correct answer?
4
What is the distance limitation of Cat5 UTP?
What is the correct answer?
4
Which of the following is used for testing the data-link connection in a PPP network?
A. Link Control Protocol (LCP)
C. Network Control Protocols (NCPs)
D. Basic Rate Interface (BRI)
What is the correct answer?
4
To communicate across a TCP/IP network, you must have a DNS server and DNS clients installed.
What is the correct answer?
4
Data Transmission is not a layer in the OSI model
What is the correct answer?
4
In ________ routing, the tunnel creates a bridge through areas that do not support
multicast traffic.
C. Border Gateway Protocol
What is the correct answer?
4
You're asked to install a Citrix MetaFrame XP server. What protocol will clients use to connect and run graphical terminal emulation to the new server?
What is the correct answer?
4
In TCP segment format _______indicates start of data.
What is the correct answer?
4
--------------- is/are used for error detection.
What is the correct answer?
4
Internet Research Task Force (IRTF) body looks after ________.
A. The research projects of TCP/IP suit
B. Technical related issues
C. Development of standards like Requests for Comments
D. Maintenance of Internet
What is the correct answer?
4
Which of the following versions will replace IPv4 Internet layer?
What is the correct answer?
4
Which piece of equipment operates at both the data-link and network layers?
What is the correct answer?
4
Which of the following address supports 254 hosts on each of 2 million networks?
What is the correct answer?
4
Which is the port used by HTTPS?
What is the correct answer?
4
Which of the following IEEE specifications uses CSMA/CD?
What is the correct answer?
4
Which of the following protocol resolves a host's hardware address for a known IP
address?
What is the correct answer?
4
FTP servers by default listen on port ________ for incoming connections from FTP clients.
What is the correct answer?
4
You have a network card with the connector in question 43, and it also has a 15 pin female connector, the pins being in two rows. What type of card is it?
What is the correct answer?
4
You've taken your Windows 2000 laptop to a client's network and plugged it in. Your computer is configured for an IP network over 100BaseT using DHCP. You can't connect, even though the client says that DHCP is working on his 100BaseT network. What should
A. Use Ipconfig /release to release the old DHCP address.
B. Use Winipcfg and click Release to release the old DHCP address.
C. Use Ifconfig to initialize the NIC.
D. Use Tracert to determine the problem.