Consider an ideal solution of components A and B. The entropy of mixing per mole of an alloy containing 50% B is
R ln 2
-R ln 2
3 R ln 2
-3R ln 2
Correct Answer :
A. R ln 2
Related Questions
Which one of the following is incombustible?
H2
CCl4
C2H2
S
Transformation range for ferrous material is the temperature interval during which __________ is formed during its heating.
Cementite
Austenite
Martensite
Pearlite
Electrolytic reduction cell used for conversion of calcined Al2O3 to Al is a carbon lined furnace operating at 800-900 °C. The purpose of electric current supplied to the furnace is to
Achieve very high purity of aluminium (99.9%)
Keep the electrolyte in liquid condition by the generation of heat
Electrolytically dissociate alumina
Both (B) & (C)
Globular form of cementite is formed during the __________ process.
Spheroidising
Hardening
Annealing
Normalising
__________ of air does not increase with increase in temperature.
Density
Thermal diffusivity
Viscosity
Thermal conductivity
Difference at any instant between the value of the controlled variable and the set point is called the
Deviation
Derivative time
Error ratio
Differential gap
Moist air is cooled along the line of constant __________ , when it is passed over a cold & dry cooling coil, such that no condensation occurs?
Enthalpy
Relative humidity
Wet bulb temperature
Dew point temperature
The friction factor for the turbulent fluid flow in a rough pipe does not depend upon the
Pipe roughness & pipe diameter
Fluid velocity
Type of flowing fluid
Both 'b' & 'c'
Which of the following is not used as a bearing material?
Copper-lead alloys
Babbitts
Bronzes
Cermets
Flue gases pass through the following boiler accessories in a high pressure natural circulation boiler.
A. Induced draft fan
B. Economiser
C. Air preheater
D. Steam superheater Which of the following gives the correct sequence of flow of the flue gases through the above mentioned boiler accessories?
A, C, B, D
D, B, C, A
D, C, B, A
D, A, B, C
Though tin occurs lower than iron in the electrochemical series, yet it is coated on steel for corrosion protection, because of its
Lower cost
Abundant availability
Resistance to vegetable acids as the tin plate are commercially used in 'canning' industry
None of these
Tesla metre per ampere (T. m/A) is the unit for the measurement of
Magnetic susceptibility
Magnetic moment
Permeability of free space
Flux density
Tempering of a material does not improve its
Machinability
Toughness
Internal stress level
Softness
The malleability of a material is the property by virtue of which it can be rolled or hammered into thin sheets. Which of the following materials has the maximum malleability?
Lead
Copper
Aluminium
Wrought iron
Magnesium is present in
Haemoglobin
Chlorophyll
Hypo solution
None of these
Material of construction of foundry crucible is
Lead
Stainless steel
Graphite
Cast iron
__________ joint is mostly used for joining pipes carrying water at low pressure.
Nipple
Socket
Union
Bell and spigot
Change in volume of metals from absolute zero temperature to their melting points is
Almost same for all metals
Different for different metals
Less for low melting point metals
Less for high melting point metals
__________ of grey cast iron produces white cast iron.
Tempering
Rapid heating
Rapid cooling
Slow cooling
The heat of neutralisation remains constant, when there is a reaction between dilute solutions of strong
Base and strong acid
Base and weak acid
Acid and weak base
None of these
__________ is not a case hardening process.
Carburising
Nitriding
Cyaniding
Annealing
In the blast furnace, incorporation of water vapour in the blast gives the following effect.
Increases the reducing potential of the gas
Increases the flame temperature
No significant change occurs
Increases the hydrogen content in the metal
Which of the following does not have a sharp melting point?
Thoria
Glass
Ice
Pig iron
For separating small pieces of metal from engine oil of a car, the best separating technique is the
Chromatography
Evaporation
Filtration
Fractional distillation
Chromium molybdenum steel cannot be welded using __________ welding.
Thermit
Electrical resistance
Oxy-acetylene
Any of these
__________ rubber is generally used for making 'O' rings used for vacuum sealings.
Natural
Neoprene
Butadiene
Nitrile
Circular cross section machine parts which are symmetrical about the axis of rotation are made by hot
Piercing
Spinning
Drawing
Extrusion
Blow off cock is provided in steam boiler to
Guard the boiler in case of abnormal rise in steam pressure
Drain out water and sludge during its repair
Regulate the supply of water in boiler
Put out the fire in the furnace when the water level in the boiler falls to unsafe limit
Increase in temperature, in general results in the
Decrease in the viscosities of both liquids & gases
Increase in the viscosities of both liquids & gases
Increase in the viscosity of liquids and decrease in that of gases
Decrease in the viscosity of liquids and increase in that of gases
The usual energy consumption in electric arc furnace steel making is __________ KWh/ton of steel.
60 - 100
400 - 700
1200 -1500
2000 - 2300