Related Questions
What is the correct answer?
4
Colour comparator is used to measure the
What is the correct answer?
4
Laser is a device to produce
D. A beam of coherent light
What is the correct answer?
4
The majority charge carriers in p-type silicon are
What is the correct answer?
4
Pearlite comprises of
A. 87% cementite & 13% Fe
B. 87% ferrite & 13% cementite
C. 93.33% ferrite & 6.67% C
What is the correct answer?
4
Projection welding & stud welding is categorised as the __________ welding.
What is the correct answer?
4
Use of water as a manometric liquid suffers from the disadvantage of its
What is the correct answer?
4
Cascade control is
A. The continuous adjustment of the set point index of an automatic control loop by a primary (master) controller
B. Used when changes in process conditions cause serious upsets in the controlled variable
C. Useful to control flow from temperature
What is the correct answer?
4
Dew point temperature always gives an indication of the __________ of the moist air.
What is the correct answer?
4
Air standard Otto cycle is more efficient than the diesel cycle for the same
A. Heat addition & compression ratio
B. Heat addition & pressure
C. Compression ratio & pressure
D. Cylinder dimension & rpm
What is the correct answer?
4
Electrolytic reduction cell used for conversion of calcined Al2O3 to Al is a carbon lined furnace operating at 800-900 °C. The purpose of electric current supplied to the furnace is to
A. Achieve very high purity of aluminium (99.9%)
B. Keep the electrolyte in liquid condition by the generation of heat
C. Electrolytically dissociate alumina
What is the correct answer?
4
The yield point phenomenon observed in annealed low carbon steel is due to the presence of the following element.
What is the correct answer?
4
The diffusion co-efficient of Ni in Cu at 1000 K is 1.93 × 10-16 m2S-1 and it is 1.94 × 10-14 m2S- 1 at 1200 K. The activation energy (in k. J.mole-1) for the diffusion of Ni in Cu is
What is the correct answer?
4
The stress at which extension of the material takes place more rapidly as compared to the increase in load is termed as the __________ point of the material.
What is the correct answer?
4
A solar cell converts the sunlight directly into __________ energy.
What is the correct answer?
4
One of the methods of purification of leach liquor is ion exchange, which involves
A. Exchange between two liquid phases
B. Exchange between a gaseous phase and a liquid phase
C. Exchange between a liquid phase and an organic resin phase
D. Exchange between a solid phase and a gas phase
What is the correct answer?
4
Photographic plates are coated with
What is the correct answer?
4
Which of the following if present in iron ore, enhances its value?
What is the correct answer?
4
Pick out the correct statement
A. Jet engine can work, where there is no atmosphere
B. Rocket engines cannot work, where there is no atmosphere
C. Rocket engines carry oxygen required for the combustion in the form of oxidiser
D. Jet engines also carry oxidiser
What is the correct answer?
4
Though tin occurs lower than iron in the electrochemical series, yet it is coated on steel for corrosion protection, because of its
C. Resistance to vegetable acids as the tin plate are commercially used in 'canning' industry
What is the correct answer?
4
Rankine cycle comprises of two isothermal and two __________ processes.
What is the correct answer?
4
The pressure drop per unit length for laminar flow of fluid through a long pipe is proportional to (where, A = cross-sectional area of the pipe & D = Diameter of the pipe)
What is the correct answer?
4
While the oxy-acetylene flame produces a temperature of 3200°C, the temperature produced by oxy-hydrogen flame is about __________ °C.
What is the correct answer?
4
Notched bar test is used for testing the __________ of a material.
What is the correct answer?
4
Unit of surface tension in S.I. unit is
B. Joule/
C. Newton/
What is the correct answer?
4
In the X-ray radiography technique, the tube voltage for thicker plates as compared to thin plates, should be
A. Higher, as it gives higher wavelength
B. Lower, as it gives higher wavelength
C. Higher, as it gives shorter wavelength
D. Lower, as it gives shorter wavelength
What is the correct answer?
4
Stresses encountered in the metal forming processes are less than the __________ of the material.
D. Limit of proportionality
What is the correct answer?
4
With decrease in the grain size of a material, its creep resistance
D. Either (A) or (B); depends on the material
What is the correct answer?
4
The minimum carbon content in steel should be __________ percent for it to respond to a hardening treatment.
What is the correct answer?
4
__________ is the process used for setting up compressive stresses in the surface of a metal to improve its fatigue strength.
What is the correct answer?
4
Which of the following has the least value of ultimate tensile strength (UTS)?