Home
Current Affairs January 2024

What is the correct answer?

4

_________ describe(s) users working from home.

A. SOHO

B. Branch office

C. Regional office

D. Corporate office

Correct Answer :

A. SOHO


Related Questions

What is the correct answer?

4

Extended IP ACLs should be placed as close to the ____________ device as possible.

A. Source

B. Destination

What is the correct answer?

4

Which 2950 command enables trunking?

A. switchport mode trunk

B. trunking on

C. trunking enable

D. switchport trunk on

What is the correct answer?

4

Which types of memory do not maintain their contents during a power-off state?

A. NVRAM

B. ROM

C. RAM

D. Flash

What is the correct answer?

4

The _________ command takes you from User EXEC mode to Privilege EXEC mode

A. DISABLE

B. ENABLE

What is the correct answer?

4

Which is not one of the three main functions of a layer-2 device?

A. Learning

B. Forwarding

C. Listening

D. Removing loops

What is the correct answer?

4

You execute the line console 0 command from Configuration mode. What will the router's prompt be?

A. Router(config)#

B. Router(config-line)#

C. Router(config-interface)#

D. Router#(config-if)

What is the correct answer?

4

The root switch is the one elected with the __________ __________.

A. Lowest MAC address

B. Highest MAC address

C. Lowest switch ID

D. Highest switch ID

What is the correct answer?

4

BPDU stands for ____________.

A. Bridge Protocol Description Unicast

B. Bridge Protocol Data Unit

C. Bridge Protocol Description Unit

D. Bridge Protocol Data Unicast

What is the correct answer?

4

The _________ is your network equipment, which includes the DCE (e.g., a modem) and the DTE (e.g., a router).

A. Demarcation point

B. Carrier switch

C. Local loop

D. CPE

What is the correct answer?

4

__________ states that if a neighboring router sends a route to a router, the receiving router will not propagate this route back to the advertising router on the same interface.

A. Split horizon

B. Poison reverse

C. Hold-down timer

D. Hop count limit

What is the correct answer?

4

Which router command specifies the ISDN switch the router is connected to?

A. isdn switch-type

B. isdn connection-type

C. isdn spid1

D. interface serial0:15

What is the correct answer?

4

Which of the following reasons might you need to use address translation?

A. You have to use public addressing because your ISP didn't assign you enough private addresses.

B. You are using private addresses but have changed ISPs, and your new ISP won't support these private addresses.

C. You want to assign the same IP address to multiple machines so that users on the Internet see this offered service as a single logical computer.

D. You are merging two companies that use different address spaces.

What is the correct answer?

4

You are in Interface Subconfiguration mode and want to completely return to Privilege EXEC mode. What would you enter? (Choose all correct answers.)

A. CTRL-Z

B. end

C. exit

D. logout

What is the correct answer?

4

When choosing a dynamic routing protocol, which of the following should not be considered?

A. Metrics used

B. How routing information is shared

C. How routing information is processed

D. Number of PCs in the network

What is the correct answer?

4

The switch port that is chosen to forward traffic for a segment is called a __________.

A. Root port

B. Alternate port

C. Backup port

D. Designated port

What is the correct answer?

4

If you enter a command in either User EXEC mode or Privilege EXEC mode that the IOS does not recognize, the switch or router

A. Logs you out

B. Tries to resolve the command to an IP address

C. Executes the closest command that it can find in its command set

D. Makes a "beep" sound

What is the correct answer?

4

You are given a class C network, 192.168.1.0/24. You need three networks with 60 hosts and two networks with 30 hosts. What are the subnet mask values you could use?

A. 255.255.255.128 and 255.255.255.192

B. 255.255.255.224 and 255.255.255.240

C. 255.255.255.192 and 255.255.255.224

D. None of these

What is the correct answer?

4

Which of the following is not an advantage of route summarization?

A. It requires less memory and processing.

B. It supports smaller routing update sizes.

C. It contains network problems.

D. It supports discontiguous subnets.

What is the correct answer?

4

Which 1900 command enables port security?

A. port security

B. switchport security

C. port secure

D. switchport port-security

What is the correct answer?

4

RIP generates routing updates every _________ seconds.

A. 15

B. 30

C. 60

D. 90

What is the correct answer?

4

A _________ provides a high-speed infrastructure to move data between storage devices and file servers.

A. SAN

B. LAN

C. CN

D. SAN and CN

What is the correct answer?

4

You have a 24-channel T1 connection to your router. How many VCs does this T1 support?

A. 1

B. 24

C. No limit

What is the correct answer?

4

Which command assigns a default gateway to the 2950 switch?

A. (config)# default-gateway

B. (config-if)# default-gateway

C. (config-if)# ip default-gateway

D. (config)# ip default-gateway

What is the correct answer?

4

You are given a Class B network with a subnet mask of 255.255.255.192. How many host
addresses are there on each subnet?

A. 30

B. 62

C. 126

D. 254

What is the correct answer?

4

___________ only translates one (and only one) IP address to another.

A. NAT

B. PAT

C. PAR

D. NAT and PAT

What is the correct answer?

4

Which of the following commands belongs on the physical interface when using dialer profiles?

A. dialer pool-member

B. dialer-group

C. ip address

D. dialer string

What is the correct answer?

4

What subnet mask would you use to set up a default route?

A. 0.0.0.0

B. 255.255.255.255

C. Depends on the type of network number

D. None of these answers

What is the correct answer?

4

VLSM allows you to summarize __________ back to the class boundary.

A. Subnets

B. Networks

What is the correct answer?

4

EIGRP generates hellos every _________ seconds on LAN segments.

A. 5

B. 10

C. 15

D. 30

What is the correct answer?

4

What must you do to enable IP routing on your router? (Choose all of the correct answers.)

A. Enable the routing protocol.

B. Set clocking on all serial interfaces.

C. Assign IP addresses to your router's interfaces.

D. Assign the bandwidth parameter to your serial interfaces