Related Questions
What is the correct answer?
4
The thread note for a typical bolt will include the ________.
A. Major diameter of the thread
What is the correct answer?
4
Given a situation in which the drafter has crossed extension lines in a drawing what can be done to clean up the point of crossing?
A. Use the Modify tool to clean up the extension lines
B. Use the Tolerance tool to clean up the extension lines
C. Use the Break tool to clean up the extension lines
D. Use the stretch tool to clean up the extension lines
What is the correct answer?
4
When drawing a line using the relative coordinate system a line is created from ________.
B. The ending point of the last line
C. The beginning point of the last line
What is the correct answer?
4
This type of thread is a thread on the inside of a member:
What is the correct answer?
4
In oblique sketches, the most commonly used angles for receding lines are:
What is the correct answer?
4
When using versions of Auto-CAD prior to Release 2006 it may be necessary to ________ a block in order to edit it.
What is the correct answer?
4
Approximately this much of the cost of product development and manufacture is determined at the design stage:
What is the correct answer?
4
Several of the tools used in traditional drafting include the following:
A. Parallel straight edge
What is the correct answer?
4
This type of solid is egg-shaped and can be created by revolving an ellipse around one of its axes:
What is the correct answer?
4
This allows the performance of structures to be analyzed and tested efficiently, accurately, and quickly:
A. Computer-aided manufacturing
C. Computer-aided engineering
D. Computer-aided prototyping
What is the correct answer?
4
In architectural drawing ________ are often used to illustrate and detail structural components.
A. Foundation beam detail sections
What is the correct answer?
4
Objects that are symmetric can be shown effectively using this type of section:
What is the correct answer?
4
This is the total amount that the feature on the actual part is allowed to vary from what is specified by the dimension:
What is the correct answer?
4
These types of projectors converge at a vanishing point:
What is the correct answer?
4
On a floor plan the dashed line that appears approximately 24 outside the exterior wall represents the __________.
What is the correct answer?
4
In some circumstances an entire drawing can be inserted into a different drawing as a block. When this is used the base point will default to ________.
What is the correct answer?
4
An Auto-CAD term that refers to a pre-drawn object which is stored in a drawing file and can be inserted into any other drawing file as needed is a ________.
What is the correct answer?
4
In multi-view drawing it is common practice to include three views, the front, the top and the right side. If no dimensions are required on the right side view the drafter can ________.
C. Use the left view instead
What is the correct answer?
4
Newer versions of Auto-CAD utilize the ________ to make block library management very easy.
What is the correct answer?
4
This is a thin solid line directing attention to a note or dimension and starting with an arrowhead or dot:
What is the correct answer?
4
In an oblique drawing, equally spaced partial circles may be used to show this:
What is the correct answer?
4
The condition of a part when it contains the least amount of material is referred to as ________.
What is the correct answer?
4
If a designer is developing a plan for a project in which the entire part is made out of ¾ thick plywood and he only wants to use one view, he should use the ________ view.
What is the correct answer?
4
These are special installations of stone or concrete marking the locations of points accurately determined by precise surveying:
What is the correct answer?
4
Most architectural drawings produced for field use by building contractors are printed on architectural D size paper which measures ________.
What is the correct answer?
4
Referring to the fractional inches to decimal inches to millimetre conversion chart on page 55 what is the equivalent mm measurement of 3/16 inch.
What is the correct answer?
4
When the receding lines are true length, and the projectors are at 45 degrees to the plane of projection, the oblique drawing is called this:
C. Axonometric projection
What is the correct answer?
4
This type of solid is formed by sweeping a shape along a linear path:
What is the correct answer?
4
Drawings created with commercial software are typically saved as:
What is the correct answer?
4
Inserting blocks into a drawing file usually requires exacting placement. The drafter should insure that ________ is turned on.