Drawings created with commercial software are typically saved as:
Rapid prototypes
Electronic files
Draft drawings
Change orders
Correct Answer :
B. Electronic files
Related Questions
One way to evenly space dimensions on a drawing is to use the ________.
Dimension Space tool
Linear tool
Continue tool
Baseline tool
In perspective drawings this is placed between the observer and the object:
Vanishing point / horizon
Station point
Ground line
Plane of projection / picture plane
This is formed where three or more surfaces intersect:
Oblique
Line
Edge
Vertex
4.The principle reason for using an auxiliary view is ________.
To eliminate hidden lines
To create a true projection plane from an inclined plane in one of the primary views
To show cylinders as ellipses
To locate center marks
If a designer is developing a plan for a project in which the entire part is made out of ¾ thick plywood and he only wants to use one view, he should use the ________ view.
Front
Top
Right
Back
A half-moon protractor is divided into how many degrees?
360
180
270
310
When adding dimensions to an auxiliary view it will be necessary to use the ________ tool.
Linear dimension
Aligned dimension
Baseline dimension
Angle dimension
This type of auxiliary view is projected onto a plane that is perpendicular to one of the principal planes of projection:
Primary
Secondary
Revolved
Successive
This is a thin solid line directing attention to a note or dimension and starting with an arrowhead or dot:
Dimension line
Extension line
Leader
Specification
Which of the following is one of the basic types of welded joints:
T-joint
Rear joint
Angle joint
Groove joint
These breaks are used to shorten the view of an object:
Section breaks
Aligned breaks
Conventional breaks
Full breaks
Generally, the units used on an architectural drawing are set to ________.
Architectural
Engineering
Metric
Civil
The site plan illustrates ________.
The floor plan
Where the house sits on the property
The roof plan
Where the garage and driveway are located
This is used to indicate that a surface is to be machined:
Finish mark
Machining mark
Roughness indicator
Coordinate mark
In this type of dimensioning, allowance must be made for bends:
Angular
Tolerance
Datum
Sheet metal
These gears transmit power between shafts whose axes intersect at any angle:
Worm gears
Spur gears
Bevel gears
Racks
An advantage of this type of view is that each view shows the object all the way through as if it were transparent:
Planar
Horizontal
Auxiliary
Orthographic
This is used in drawings to represent the edge of a solid object:
Angle
Vertex
Surface
Line
In this type of auxiliary view, a break line is used to indicate the imaginary break in the views:
Primary
Secondary
Revolved
Partial
In the section view, the areas that would have been in actual contact with the cutting plane are shown with:
A cutting plane line
Section lining
Visible lines
Lines and arrows
Architectural drafters generally prefer to use ________ drawings to help illustrate 3-dimensional views of a structure.
Isometric
Perspective
Orthographic
Auxiliary
This means that a feature of a finished product contains the maximum amount of material permitted by the tolerance dimensions for that feature:
Maximum material condition
Machined material condition
Maximum machined indication
Machine mark indication
EDM is the acronym for:
Enterprise data management
Engineering drawing management
Enterprise drawing manipulation
Engineering data manipulation
In an exploded assembly drawing it is customary for the drafter to use a ________ line to illustrate how parts fit together.
Phantom
Hidden
Dashed
Center
In this type of projection, each of the axes has different ratios of foreshortening:
Isometric
Dimetric
Trimetric
Parallel
Auto-CAD refers to isometric ellipses as ________.
Ellipses
Iso-ellipses
Iso-circles
Circles
This is the plane upon which the top view is projected:
Horizontal
Frontal
Profile
Base
Baseline dimensions are referenced from a common geometric feature known as a ________.
Edge
Corner
Datum
Point of reference
The UCS icon represents the intersection of the ________.
X-axis
Y-axis
Z-axis
All of the above
The Press-Pull tool will ________ the face of a solid model in the direction it faces.
Taper
Extrude
Spiral
None of the above