Related Questions
What is the correct answer?
4
Traditional drafters need to be able to create several different line widths because ________.
A. Different line widths convey different information
B. The line width has to do with how dark it appear in the finished drawing
C. They seem to transmit better in a fax machine
D. It makes no difference
What is the correct answer?
4
In offset sections, offsets or bends in the cutting plane are all:
C. Either 90 or 180 degrees
What is the correct answer?
4
The bounding box method for setting up an isometric drawing helps the drafter ________.
A. Confine the isometric drawing to its maximum size
B. Figure what lines are to be illustrated vertical and horizontal
C. Position the isometric drawing in paper space
What is the correct answer?
4
One way to evenly space dimensions on a drawing is to use the ________.
What is the correct answer?
4
This type of section is not in direct projection from the view containing the cutting plane:
What is the correct answer?
4
Angles project true size only when the plane containing the angle and plane of projection are this:
What is the correct answer?
4
Understanding the Cartesian coordinate system will help the beginning drafter ________.
A. Control the accuracy of the drawing
B. Produce a visible grid system
C. Select a different text style
D. Choose various line types
What is the correct answer?
4
Architectural dimensioning is usually done in ________.
What is the correct answer?
4
One critical issue drafters need to pay close attention to is the ________.
What is the correct answer?
4
This is a thin solid line directing attention to a note or dimension and starting with an arrowhead or dot:
What is the correct answer?
4
4.The principle reason for using an auxiliary view is ________.
A. To eliminate hidden lines
B. To create a true projection plane from an inclined plane in one of the primary views
C. To show cylinders as ellipses
D. To locate center marks
What is the correct answer?
4
Newer versions of Auto-CAD utilize the ________ to make block library management very easy.
What is the correct answer?
4
In an oblique drawing, equally spaced partial circles may be used to show this:
What is the correct answer?
4
This type of surface is tipped to all principal planes of projection and does not appear true size in any standard view:
What is the correct answer?
4
Oblique sections are useful to show this:
A. Foreshortened features
What is the correct answer?
4
In order to create an accurate assembly drawing the drafter should create the ________ drawings first.
What is the correct answer?
4
This type of auxiliary view is projected onto a plane that is perpendicular to one of the principal planes of projection:
What is the correct answer?
4
When dimensioning piping drawings, you give the lengths of all runs of this type:
What is the correct answer?
4
On a floor plan the dashed line that appears approximately 24 outside the exterior wall represents the __________.
What is the correct answer?
4
The Auto-CAD command used to combine two or more primitive shapes into a single complex 3-dimensional model is ________.
What is the correct answer?
4
Drawings created with commercial software are typically saved as:
What is the correct answer?
4
The principle views associated with orthographic projection are ________.
What is the correct answer?
4
The text height for room names should be set to ________for a drawing that will be plotted to a scale of ¼ = 1'-0.
What is the correct answer?
4
An engineer's scale would be used to measure lines on a drawing where the scale factor reads ________.
What is the correct answer?
4
Baseline dimensions are referenced from a common geometric feature known as a ________.
What is the correct answer?
4
Once the architect has finalized the house plans with the client any changes to the design requested by the client will require a ________.
C. Whole new set of drawings
What is the correct answer?
4
This is used in drawings to represent the edge of a solid object:
What is the correct answer?
4
Before starting an isometric drawing in Auto-CAD the drafter needs to ________.
A. Set the grid to isometric
B. Set the current layer to Defpoints
What is the correct answer?
4
The building construction industry relies on sets of ________ drawings to construct homes and commercial buildings.
What is the correct answer?
4
The ________ is a standard element of a section view in a technical drawing.
C. Material hatch pattern