Related Questions
What is the correct answer?
4
Wohler test is a destructive test to find out the __________ strength of a prepared metal specimen.
What is the correct answer?
4
At 100% relative humidity, the dew point temperature of moist air is
A. Less than the wet bulb temperature
B. More than the wet bulb temperature
C. Equal to the wet bulb temperature
D. Equal to the ambient temperature
What is the correct answer?
4
__________ can replace tungsten in high speed steel.
What is the correct answer?
4
Diamagnetic materials
A. Are magnetised by eddy currents only
B. Are non-magnetic and cannot be magnetised
C. Are magnetised in direction opposite to the magnetic field
D. Can be magnetised in one direction only
What is the correct answer?
4
The most suitable material for die casting is
What is the correct answer?
4
Induced draft fans provided in large thermal power plant boilers have __________ blades.
What is the correct answer?
4
A solar cell converts the sunlight directly into __________ energy.
What is the correct answer?
4
Which of the following has the least value of ultimate tensile strength (UTS)?
What is the correct answer?
4
Pick out the correct statement.
A. Hot worked materials are subjected to annealing to remove internal stresses
B. Annealing of steel hardens it slightly
C. Normalising of a material induces stresses
D. Tempering of a material improves ductility & toughness but reduces hardness & brittleness
What is the correct answer?
4
The only suitable method for hardening the low carbon steel is case hardening. Which of the following is a case hardening process?
What is the correct answer?
4
Diameter of the rivet to be provided on a 20 mm. thick boiler plate will be __________ mm.
What is the correct answer?
4
A furnace is made of a refractory brick wall of thickness 0.5 metre and thermal conductivity 0.7 W/m.°K For the same temperature drop and heat loss, this refractory wall can be replaced by a layer of diatomaceous earth of thermal conductivity 0.14 W/m.K and thickness __________ metre.
What is the correct answer?
4
Hot working of lead is carried out at
What is the correct answer?
4
Pick out the wrong statement.
A. Weldability of high carbon steel is poorer compared to low carbon steel
B. Invar is a magnetic alloy
C. Magnetic permeability of the diamagnetic material is less than one
D. Martenistic transformation never goes to completion (i.e., 100%) at room temperature
What is the correct answer?
4
Age hardening is connected with
What is the correct answer?
4
Air intake for an air compressor should be preferably taken from
A. A site, where cooling towers are located nearby
B. A site, where open coal yard in located nearby
C. An air conditioned room maintained at a temperature of 18°C
D. An outside atmosphere at 10°C
What is the correct answer?
4
Drossing is a __________ operation.
What is the correct answer?
4
__________ rubber is generally used for making 'O' rings used for vacuum sealings.
What is the correct answer?
4
An approximately __________ process exemplifies the flow of a gas through a very long pipe of uniform cross-section.
What is the correct answer?
4
__________ flux is used for the extraction of metal from its self fluxing ores.
What is the correct answer?
4
In a counter flow heat exchanger, hot fluid enters at 170°C & leaves at 150°C, while the cold fluid enters at 50°C & leaves at 70°C. The arithmetic mean temperature difference in this case is __________ °C.
What is the correct answer?
4
Main constituent of bone ash is
What is the correct answer?
4
Which of the following is not a ferromagnetic material?
What is the correct answer?
4
Mild steel has __________ crystal lattice structure.
A. Face centred cubic (fcc)
B. Body centred cubic (bcc)
What is the correct answer?
4
Temperature of hot gases flowing in a pipe is measured by a thermocouple inserted in the thermal well. The thermal well made of __________ will facilitate the most accurate measurement of the temperature.
What is the correct answer?
4
Oxide layer formed on the non-ferrous metal surface after its annealing is
A. Removed by acid pickling
B. Hammered into the surface
C. Removed with coarse emery cloth
D. Left as such to protect the surface
What is the correct answer?
4
The underground well of a biogas plant is called the
What is the correct answer?
4
The materials which fracture even at small strains are termed as brittle, while those materials which exhibit an appreciable deformation before failure are termed as
What is the correct answer?
4
Calorific value of __________ are almost same.
A. Lignite & anthracite coal
D. Coal gas & natural gas
What is the correct answer?
4
Stellite is a __________ material.
D. Non-ferrous cast alloy cutting tool