Related Questions
What is the correct answer?
4
Dielectric
A. Is an electrical insulating material
B. Of low resistivity is preferred
C. Should have high thermal conductivity
D. Need not defy the corrosive action of chemicals
What is the correct answer?
4
The process of removal of scale formed during hot rolling of steel is termed as
What is the correct answer?
4
The usual energy consumption in electric arc furnace steel making is __________ KWh/ton of steel.
What is the correct answer?
4
Compressed dry air is used as the cutting fluid, while machining
What is the correct answer?
4
Satellites burn off during re-entry to earth's atmosphere, because of the
B. Gravitational pull by earth
C. Friction with earth's atmosphere
D. Loss in weight of the satellite
What is the correct answer?
4
Sudden fall of atmospheric pressure by a large amount is an indication of the
What is the correct answer?
4
Ammonia leakage in the refrigeration system is detected by
A. Sulphur stick, which on detection gives white smoke
B. Using chemical reagents
What is the correct answer?
4
Lead is poured into the joints between two __________ pipes.
What is the correct answer?
4
Transformation range for ferrous material is the temperature interval during which __________ is formed during its heating.
What is the correct answer?
4
Which of the following is an acidic constituent of B.F. slag?
A.
What is the correct answer?
4
The maximum stress below which a material can withstand an infinite number of cycle of stress, is termed as the
What is the correct answer?
4
All the atoms of the world comprise of electrons, proton & neutron except that of __________ atom in which neutron is absent.
What is the correct answer?
4
Uniform ramming of sand in green sand moulding process leads to
A. Reduced chance of gas porosity
B. Greater dimensional stability of the casting
C. Uniform flow of molten metal into the mould cavity
D. Less sand expansion type of casting defect
What is the correct answer?
4
Work required for compression of a gas contained in a cylinder is 7000 kJ. During compression, heat interaction of 3000 kJ causes the surroundings to be heated. Internal energy change of the gas during the compression is __________ kJ.
What is the correct answer?
4
Larger length & diameter water pipes are made by
A. Electrical resistance welding
C. Semi-centrifugal casting
What is the correct answer?
4
An abrupt and sudden fall in the reading of barometer is an indication of the
What is the correct answer?
4
With increase in __________ Knocking tendency in a spark ignition petrol engine decreases.
What is the correct answer?
4
Absolute zero pressure can be attained at a temperature of
What is the correct answer?
4
While the recrystallisation temperature for pure metals is 0.3 Tm, the same for alloys is equal to __________ × Tm (where, Tm Melting temperature).
What is the correct answer?
4
__________ test determines the yield strength, Young's modulus of elasticity, percentage reduction in area & percentage elongation of a material.
What is the correct answer?
4
A furnace is made of a refractory brick wall of thickness 0.5 metre and thermal conductivity 0.7 W/m.°K For the same temperature drop and heat loss, this refractory wall can be replaced by a layer of diatomaceous earth of thermal conductivity 0.14 W/m.K and thickness __________ metre.
What is the correct answer?
4
Methyl orange indicator turns
A. Orange yellow in alkaline medium
B. Orange yellow in acidic medium
C. Colourless in acidic medium
D. Colourless in basic medium
What is the correct answer?
4
Tempering of a material does not improve its
What is the correct answer?
4
Joining of thin foils is preferred to be done by
What is the correct answer?
4
Which of the following is not an explosive?
What is the correct answer?
4
The same volume of all gases is representative of their
C. Gas characteristic constants
What is the correct answer?
4
Pick out the correct combination about the role of various additives used in polymers.
A. Plasticiser: increases the polymer strength
B. Heat stabiliser: increases the maximum service temperature
C. Fillers: Does not affect the property of polymer but increases its weight
D. Lubricants: increases the flexibility of polymers
What is the correct answer?
4
Which of the following gases cause global warming?
What is the correct answer?
4
Capacity & power requirement for an air compressor working at high altitude compared to sealevel will be
D. Either more or less; depends on the climatic conditions
What is the correct answer?
4
Common salt is produced from sea water in India generally by the __________ method.