Related Questions
What is the correct answer?
4
Atomic __________ is a whole number for an element.
What is the correct answer?
4
Auto collimator is used to check
What is the correct answer?
4
Cascade control is
A. The continuous adjustment of the set point index of an automatic control loop by a primary (master) controller
B. Used when changes in process conditions cause serious upsets in the controlled variable
C. Useful to control flow from temperature
What is the correct answer?
4
Hot working of lead is carried out at
What is the correct answer?
4
Gage pressure within a spherical droplet of a fluid is 'p'. What will be gage pressure within a bubble of the same size & of the same fluid?
What is the correct answer?
4
Wrought iron does not have
A. Uniform strength in all directions
B. Ability to hold protective coating
C. High ductility & corrosion resistance
D. Easily weldable characteristics
What is the correct answer?
4
In the Bayer's process, bauxite is digested under pressure using
What is the correct answer?
4
Often earing defects are found during deep drawing operation, because the
A. Surface finish of the sheet is poor
B. Sheet material has been given substantial spring back
C. Starting sheet has planer anisotropy due to its texture
D. Starting sheet has normal anisotropy due to its texture
What is the correct answer?
4
Which of the following performance characteristics of a S.I engine is not affected by the front end volatility of the petrol used?
What is the correct answer?
4
Heating of ferromagnetic materials to a temperature above Curie temperature makes it
A. Insulator for heat & electricity transmission
C. Behave like paramagnetic materials
What is the correct answer?
4
Lead pencil contains
What is the correct answer?
4
The dew point of moist air becomes __________ with decrease in its relative humidity.
A. Less than the wet bulb temperature
B. More than the wet bulb temperature
C. More than the dry bulb temperature
D. Equal to wet bulb temperature
What is the correct answer?
4
Diameter of the rivet to be provided on a 20 mm. thick boiler plate will be __________ mm.
What is the correct answer?
4
The life of a ball bearing is inversely proportional to
What is the correct answer?
4
To improve the machinability of steel, it is generally subjected to
What is the correct answer?
4
Spheroidising of a material is a/an __________ process.
What is the correct answer?
4
Projection welding & stud welding is categorised as the __________ welding.
What is the correct answer?
4
The best lubricants for a machine working at high temperature & load is
What is the correct answer?
4
The delivery pressure of boiler feed water pump compared to the boiler steam pressure is
What is the correct answer?
4
A cylindrical rod subjected to a tensile strain within the elastic limit undergoes a volume change. If the volume strain is equal to half the tensile strain, then the Poisson's ratio of the rod is
What is the correct answer?
4
The materials which fracture even at small strains are termed as brittle, while those materials which exhibit an appreciable deformation before failure are termed as
What is the correct answer?
4
Normalising does not __________ of a metal.
A. Improve machinability & tensile strength
B. Remove internal stresses
D. Remove strains caused by cold working
What is the correct answer?
4
Absolute zero, pressure will occur, when the molecular momentum of the system becomes zero. A liquid will cease to exist as liquid at
What is the correct answer?
4
Which of the following is an acidic constituent of B.F. slag?
A.
What is the correct answer?
4
Pick out the wrong statement.
A. Molecules with symmetrical arrangements (e.g. CH4 or CCl4) are non-polar
B. Generally, non-polar compounds are chemically inactive, conduct electricity poorly and do not ionise
C. Most of the hydrocarbons are non-polar
What is the correct answer?
4
With increase in temperature, the electrical conductivity of a __________ decreases.
What is the correct answer?
4
As the fluid flow rate increases, the float of the Rotameter
B. Rotates at higher speed
C. Rotates at lower speed
D. Drops down in the tube
What is the correct answer?
4
The most important requirement for aluminium industry is the availability of cheap
What is the correct answer?
4
Temper brittleness of a material can be fairly detected by the __________ test.
What is the correct answer?
4
LVDT used for displacement measurement is a/an __________ transducer.