Related Questions
What is the correct answer?
4
Minimum number of members required to form a Public Limited Joint Stock Com-pany is
What is the correct answer?
4
Which of the following approaches the ideal gas behaviour most closely?
What is the correct answer?
4
Which of the following is not the commercial name of poly-methyl-methacrylate (PMMA)?
What is the correct answer?
4
The dimensional formula of bulk modulus of elasticity is same as that of the
What is the correct answer?
4
A material being tested for endurance strength is subjected to the __________ load.
What is the correct answer?
4
Silicon percentage in the silicon steel used for electrical appliances/equipments is
What is the correct answer?
4
Stellite is a __________ material.
D. Non-ferrous cast alloy cutting tool
What is the correct answer?
4
Tin based white metals are used, where bearings are subjected to
What is the correct answer?
4
Larger length & diameter water pipes are made by
A. Electrical resistance welding
C. Semi-centrifugal casting
What is the correct answer?
4
A spring material should have low
What is the correct answer?
4
Resistance of an electrical conductor is proportional to its (where, l = length and A = cross-sectional area of the conductor)
What is the correct answer?
4
Hardening of steel is not possible, unless it is heated __________ critical point.
C. Between the first & second
D. Between the second & third
What is the correct answer?
4
What is the range of tempering temperature (°C) for most of the materials?
What is the correct answer?
4
Pick out the wrong statement.
A. Geothermal energy is a non-conventional source of energy
B. Mass is converted into energy in both nuclear fission & fusion reaction
C. Inhalation of mercury vapour is not harmful for human beings
D. Inhalation of arsenic causes cancer
What is the correct answer?
4
With increase in steam pressure, its specific volume decreases
A. Rapidly first and then slowly
C. Slowly first and then rapidly
What is the correct answer?
4
Half life of a radioactive isotope corresponds to the time required for half of the __________ to decay.
What is the correct answer?
4
Which of the following metals is not subjected to electrolytic refining/purification?
What is the correct answer?
4
The swift cup test evaluates the following property of a sheet metal.
What is the correct answer?
4
While the recrystallisation temperature for pure metals is 0.3 Tm, the same for alloys is equal to __________ × Tm (where, Tm Melting temperature).
What is the correct answer?
4
With decrease in the grain size of a material, its creep resistance
D. Either (A) or (B); depends on the material
What is the correct answer?
4
Identify the correct statement with reference to the extractive metallurgy of aluminium.
A. The electrolyte consists of molten Na3AlF6 with approximately 1 to 8% Al2O3
B. Approximately 80% of the aluminium deposited on the cathode comes from cryolite
C. Sodium is deposited along with aluminium, but is immediately vaporised
D. Anode effect sets in when the cryolite concentration goes below 40%.
What is the correct answer?
4
Heat release during phase change is observed in case of a/an
What is the correct answer?
4
__________ is the hardest material out of the following.
What is the correct answer?
4
__________ has a negative co-efficient of linear expansion.
What is the correct answer?
4
A pycnometer is used for the measurement of
A. Flow rate of molten metal
B. Specific gravity of a liquid
D. Concentration of a solution
What is the correct answer?
4
The rolling process cannot be used to produce
What is the correct answer?
4
Corrosion rate cannot be lowered by reducing the __________ of the corroding medium.
What is the correct answer?
4
Which one of the following is incombustible?
What is the correct answer?
4
Austempering of steel requires it to be heated to 875°C followed by sudden cooling to 250-525°C, thereby changing austenite to
What is the correct answer?
4
With increase in annealing temperature, the following defect density decreases.