Related Questions
What is the correct answer?
4
Faraday's law of electrolysis is related to the
B. Atomic number of the cation
C. Equivalent mass of the electrolyte
What is the correct answer?
4
The ratio of thermal & electrical conductivity is same for all the metals at the same temperature; and at around room temperature, this ratio is proportional to(where, T = absolute temperature, °K)
What is the correct answer?
4
__________ flux is used for the extraction of metal from its self fluxing ores.
What is the correct answer?
4
Vernier calipers cannot be used to measure the
A. I.D. & O.D. of the shaft
D. Clearance between two mating surfaces
What is the correct answer?
4
Property responsible for the talcum powder to cling to the skin is the
What is the correct answer?
4
Fibre reinforced plastic (FRP) are
A. Made of glass fibre and thermoplastic resins
C. Made of thermosetting resin and glass fibre
What is the correct answer?
4
__________ iron is produced by the annealing of white cast iron.
What is the correct answer?
4
High endurance limit of carburised machine parts is because of the fact that carburisation
A. Suppresses any stress concentration produced in the parts
B. Enhances the yield point of the material
C. Introduces a compressive layer on the surface
D. Produces a better surface finish
What is the correct answer?
4
Hollow shafts can be made as strong as solid shafts by making the twisting moments of both the shafts same. Shafts made by __________ have residual stresses.
What is the correct answer?
4
Young's modulus of a material is the measure of its
What is the correct answer?
4
Nusselt number is related to the Reynolds number (Re) in turbulent & laminar flow respectively as
What is the correct answer?
4
Iron content in Indian iron ore is about __________ percent.
What is the correct answer?
4
The temperature at which ferromagnetic material can no longer be magnetised by the outside forces, is termed as the
What is the correct answer?
4
Regeneration of molecular sieve requires it to be heated to a temperature of about __________ °C.
What is the correct answer?
4
Principal alloying elements of cast tool alloys which have very high wear resistance & high temperature strength are
A. Cobalt, chromium & tungsten
B. Cobalt, chromium & nickel
C. Molybdenum, tungsten & chromium
D. Cobalt, zirconium & molybdenum
What is the correct answer?
4
Saturated steam at a pressure of 25 kg/cm2 is throttled to attain 5 kg/cm2. Then the outcoming steam will be
What is the correct answer?
4
'GASOHOL' widely used in Brazil as a motor fuel is a mixture of alcohol and
C. Light hydrocarbon gases (e.g. butane or propane)
What is the correct answer?
4
Which of the following varies as the square root of oil pressure during atomisation of fuel oil through a pressure jet burner?
What is the correct answer?
4
The passage between the nozzle and the __________ is called 'sprue' in case of injection moulding.
What is the correct answer?
4
What is the critical radius of insulation (cms) for a metallic cylinder, if the convective heat transfer co-efficient with the ambient atmosphere is 5 W/m2. °K? Thermal conductivity of metal and insulation material are 40 and 0.1 W/m.°K respectively.
What is the correct answer?
4
Satellites burn off during re-entry to earth's atmosphere, because of the
B. Gravitational pull by earth
C. Friction with earth's atmosphere
D. Loss in weight of the satellite
What is the correct answer?
4
Cold chisels hammers are made of
What is the correct answer?
4
The substance used as a smoke screen in warfare is
What is the correct answer?
4
Which of the following metals reacts violently with water?
What is the correct answer?
4
With increase in compression ratio, the volumetric efficiency of air compressor
D. May increase or decrease (depends on the suction pressure)
What is the correct answer?
4
Alloying elements present in Haynes stellite, which has superior performance than high speed steel, are:
A. Nickel, cobalt & chromium
B. Tungsten, chromium & cobalt
C. Manganese, chromium & cobalt
D. Tungsten, molybdenum & nickel
What is the correct answer?
4
Increase in the entropy of a system represents the
B. Decrease in system pressure
C. Increase in the availability of energy
D. Increase in the temperature
What is the correct answer?
4
Which of the following low melting alloy containing bismuth and lead is used for electric fuse?
What is the correct answer?
4
Which of the following approaches the ideal gas behaviour most closely?
What is the correct answer?
4
According to maximum shear stress failure criterion, yielding in material occurs, when the maximum shear stress is equal to __________ times the yield stress.