Related Questions
What is the correct answer?
4
The ratio of thermal & electrical conductivity is same for all the metals at the same temperature; and at around room temperature, this ratio is proportional to(where, T = absolute temperature, °K)
What is the correct answer?
4
The units of the rate constant for a second order reaction are
What is the correct answer?
4
The activity of pure hydrogen gas at 1000°C and 5 atm pressure
B. Is always greater than 1
D. Depends on the choice of the standard state
What is the correct answer?
4
Nitriding of a steel part does not increase its
What is the correct answer?
4
The kinematic viscosity (in stoke) and the absolute/dynamic viscosity (in poise) are the same for __________ at room temperature.
What is the correct answer?
4
With increase in steam pressure, its specific volume decreases
A. Rapidly first and then slowly
C. Slowly first and then rapidly
What is the correct answer?
4
To counteract the bad effects of strain hardening on a cold formed part, it must be
What is the correct answer?
4
Heat flow across a hollow sphere of inner radius 'r1' and outer radius 'r2' is directly proportional to
What is the correct answer?
4
Out of the following __________ iron has the best capability to bear sudden & excessive shocks.
What is the correct answer?
4
An alloy of Fe - 0.4 % C is
What is the correct answer?
4
__________ property of a material is determined by the Herbert Pendulum device.
What is the correct answer?
4
Property responsible for the talcum powder to cling to the skin is the
What is the correct answer?
4
Nickel is a __________ material.
What is the correct answer?
4
In case of simple harmonic motion, displacement is proportional to the
What is the correct answer?
4
For efficient performance of a blast furnace, the extent of reduction of Wustite (FeO) should be
A. 100% indirect reduction
C. 50-60% indirect reduction
D. 30-40% indirect reduction
What is the correct answer?
4
A highly elastic material is deformed least on loading and retains its original form on removal of the load. Which of the following is the most elastic material?
What is the correct answer?
4
Hardening of steel is not possible, unless it is heated __________ critical point.
C. Between the first & second
D. Between the second & third
What is the correct answer?
4
Laser is a device to produce
D. A beam of coherent light
What is the correct answer?
4
Reynolds number of a fluid flowing in a circular pipe is 10,000. What will be the Reynolds number when the fluid velocity is decreased by 30% & the pipe diameter is increased by 30%?
What is the correct answer?
4
The cooling rate required to freeze 1 ton of water at 0°C into ice at 0°C in 24 hours is __________ BTU/hr.
What is the correct answer?
4
If the demand for an item is trebled and the order cost is reduced to one third, then the economic order quantity
C. Decreases by a factor of 3
D. Decreases by a factor of 1/3
What is the correct answer?
4
The amount of water evaporated in kg per kg of fuel burnt in a boiler is called the __________ of a boiler.
B. Evaporation efficiency
What is the correct answer?
4
Thermodynamic cycle involved in the working of a thermal power plant is the __________ cycle.
What is the correct answer?
4
Fatigue limit improvement by over stressing the metal by successively increasing the load is called coaxing. In fatigue failure, the material fails
C. Below the elastic limit
What is the correct answer?
4
At absolute zero temperature, for any reaction involving condensed phases
What is the correct answer?
4
__________ glass is used in the mercury in glass thermometer meant for measuring a temperature of 500°C.
What is the correct answer?
4
Titanium is produced by __________ of Ti Cl4.
A. Electrolytic reduction
What is the correct answer?
4
Percentage of differential pressure lost in a Venturimeter with a tapering of 15° may be about
What is the correct answer?
4
The materials which fracture even at small strains are termed as brittle, while those materials which exhibit an appreciable deformation before failure are termed as
What is the correct answer?
4
The function of neutral flux used in the pyrometallurgy of metal extraction is to increase the __________ of the slag.