Related Questions
What is the correct answer?
4
This type of solid has two bases that are parallel equal polygons:
What is the correct answer?
4
A civil engineer working on a bridge design would probably rely on his ________ scale for checking printed drawings.
What is the correct answer?
4
When designing a home for a client, one of the most important predesign considerations that an architect needs to address is ________.
A. How much money the client is willing to spend
B. The site on which the house is to sit
C. The nearest grocery store
D. Whether or not there is a curb and gutter system
What is the correct answer?
4
Several of the tools used in traditional drafting include the following:
A. Parallel straight edge
What is the correct answer?
4
The architectural drafter usually begins a set of working drawings by creating the ________ plan first.
What is the correct answer?
4
In this type of dimensioning, allowance must be made for bends:
What is the correct answer?
4
In order to create an isometric circle to represent a hole through the top surface of a box, the drafter must insure that the correct iso-plane has been selected by scrolling through the iso-planes using the ________ key.
What is the correct answer?
4
Referring to the fractional inches to decimal inches to millimetre conversion chart on page 55 what is the equivalent mm measurement of 3/16 inch.
What is the correct answer?
4
Switches and relays should be shown in this position with no operating force or applied energy:
What is the correct answer?
4
In perspective drawings this is placed between the observer and the object:
A. Vanishing point / horizon
D. Plane of projection / picture plane
What is the correct answer?
4
This line pattern is composed of three dashes, one long dash on each end with a short dash in the middle:
What is the correct answer?
4
This is a flat or rounded tab protruding from a surface, usually to provide a method for attachment:
What is the correct answer?
4
One critical issue drafters need to pay close attention to is the ________.
What is the correct answer?
4
To avoid having to dimension to a hidden feature the drafter can utilize a ________ section.
What is the correct answer?
4
These are vertical distances above a common datum, reference plane, or point:
What is the correct answer?
4
The foundation contractor will work with the following architectural plans.
What is the correct answer?
4
This is the smallest diameter of a screw thread:
A. Internal thread diameter
D. External thread diameter
What is the correct answer?
4
The title block used on working drawings should include the __________.
What is the correct answer?
4
4.The principle reason for using an auxiliary view is ________.
A. To eliminate hidden lines
B. To create a true projection plane from an inclined plane in one of the primary views
C. To show cylinders as ellipses
D. To locate center marks
What is the correct answer?
4
One way to evenly space dimensions on a drawing is to use the ________.
What is the correct answer?
4
If a designer is developing a plan for a project in which the entire part is made out of ¾ thick plywood and he only wants to use one view, he should use the ________ view.
What is the correct answer?
4
This is a line terminated by arrowheads, indicating the direction and extent of a dimension:
What is the correct answer?
4
These are used to attach parts to a cylinder so they won't turn on it:
B. Key-seats and bearings
D. Keys and keyways/key-seats
What is the correct answer?
4
This is the theoretically exact size from which limits of size are determined:
What is the correct answer?
4
When using the direct entry method to create a horizontal line exactly three inches long the drafter should ________ first.
A. Pull the line from away from the starting point very carefully
B. Insure that Ortho is on
C. Enter 3 for the length of the line
D. Read the coordinate position on the Dynamic Readout
What is the correct answer?
4
Using the Relative Polar Coordinate System to add a 3 inch line that is 45 degrees from the end point of the line created above the drafter would ________.
B. Type 3 back slash and enter
C. Type 3 forward slash and enter
D. Type 3 and try to use the Dynamic Input readout to find the end point
What is the correct answer?
4
The View toolbar will position the view of the 3-D solid toward the ________.
What is the correct answer?
4
This type of surface may be a plane, a single curved surface, or a warped surface:
What is the correct answer?
4
This is used to indicate that a surface is to be machined:
What is the correct answer?
4
In oblique projection, important shapes should be in this position relative to the viewing plane: