Related Questions
What is the correct answer?
4
Out of the following, the alloy which has equal percentage of constituents, is
What is the correct answer?
4
Annealing of white cast iron produces __________ iron.
What is the correct answer?
4
An alloy of Fe - 0.4 % C is
What is the correct answer?
4
Which of the following metals reacts violently with water?
What is the correct answer?
4
Pressure exerted by a liquid depends upon its
What is the correct answer?
4
Pick out the wrong statement.
A. Weldability of high carbon steel is poorer compared to low carbon steel
B. Invar is a magnetic alloy
C. Magnetic permeability of the diamagnetic material is less than one
D. Martenistic transformation never goes to completion (i.e., 100%) at room temperature
What is the correct answer?
4
Sand used to stop the green sand from sticking to the pattern is termed as the __________ sand.
What is the correct answer?
4
In a boundary layer developed along the flow, the pressure decreases in the downstream direction. The boundary layer thickness in this case will
What is the correct answer?
4
Consider the equilibrium A(g) + B(g) = AB(g). When the partial pressure of A is 10-2 atm, the partial pressure of B is 10-3 atm and the partial pressure of AB is 1 atm, the equilibrium constant 'K' is
What is the correct answer?
4
Liquor poisoning generally occurs due to the presence of __________ in it.
What is the correct answer?
4
Direct conversion of thermal energy to electrical energy is facilitated by the
C. Magneto hydrodynamic generator
What is the correct answer?
4
Which of the following are made out of the carbon steel having carbon content of 0.9 to 1%?
A. Small punches, broaches reamers and springs
B. Cutlery, screws, rivets and files
C. Mandrels, twist drills, small lathe tools and razors
D. Forgings like can shaft, structural steel plate, threading dies and drawing dies
What is the correct answer?
4
Work required for compression of a gas contained in a cylinder is 7000 kJ. During compression, heat interaction of 3000 kJ causes the surroundings to be heated. Internal energy change of the gas during the compression is __________ kJ.
What is the correct answer?
4
On being hit with a hammer, __________ will readily fracture.
What is the correct answer?
4
A polymer is termed as an 'elastomer', if its percentage elongation is more than 100%. An elastomer is termed as 'rubber' if its percentage elongation is more than __________ percent.
What is the correct answer?
4
The product of a commercial direct reduction process is
D. Iron saturated with carbon
What is the correct answer?
4
Boiling point of water gets lowered at high altitudes (e.g., hills), because
B. Atmospheric pressure is low
C. Atmospheric pressure is high
What is the correct answer?
4
Two solutions A1 & A2 have pH value of 2 & 6 respectively. It implies that the solution
A. A1 is more alkaline than solution A2
C. A2 is very slightly acidic
What is the correct answer?
4
Euler number is defined as the ratio of inertia force to __________ force.
What is the correct answer?
4
Brazing is the joining of metals
A. Without melting the base metal
B. With a non-ferrous filler
What is the correct answer?
4
The process of removal of scale formed during hot rolling of steel is termed as
What is the correct answer?
4
X-rays are
D. Of higher wavelength than visible light
What is the correct answer?
4
The effect of friction on the flow of steam through a nozzle is to decrease the __________ of steam.
What is the correct answer?
4
Maximum amount of thermal radiation is emitted at all wavelengths at any specified temperature by a/an __________ body.
What is the correct answer?
4
For a spontaneous natural process at constant temperature and pressure, the free energy of the system always
D. Increases to a maximum before decreasing
What is the correct answer?
4
Heat required to raise the temperature of a body by 1 °C is called its
B. Specific heat capacity
What is the correct answer?
4
Fahrenheit and Centigrade scales have the same readings at
What is the correct answer?
4
On oscilloscope screen for dynamic measurement, lissajous diagram is normally used to determine the __________ of the input signal.
What is the correct answer?
4
Which of the, following is not associated with the functioning of a petrol engine?
A. Compression ignition system
What is the correct answer?
4
The refrigerant freon-12 is chemically